Tests list
TESTS LIST
This page briefly lists the extensive range of tests and analyzes that the MATED S.r.l. performs regularly.
If the method of your interest does not appear, we invite you to contact our technicians for further verification.
| Standard | Title |
|---|---|
| 2-II-3 LIGHT AGEING | Xenon light ageing |
| AER(EP).M-P-001 par.4.2.16 | Resistance to agents |
| AER(EP).M-P-001 par.4.2.18 | Resistance to damp heat |
| AER(EP).M-P-001 par.4.2.19 | Resistance to filiform corrosion |
| AER(EP).M-P-001 par.4.2.23 | Paint stripping |
| AfPS GS PAK | Polycyclic aromatic hydrocarbons (PAH) - PAH research |
| AITM 2.0007 | Aircraft Interior Materials - Specific optical smoke density |
| ALSTOM DTRF150606 Version C - Appendix 3 | Standard bogie paints - Determination of ice removal bahaviour |
| ALSTOM DTRF150612 rev.A | Coating - Evaluation of resistance to cleaning agents and graffiti removal |
| Analisi additivi polimero con GC/MS o LC/MS | GC-MS -LC-MS additives-polymer - Quantitative analysis of additives in polymer by using GC-MS-LC-MS |
| Analisi al microscopio | Microscope analysis |
| Analisi Chimiche | Chemical analysis |
| ANALISI LECO | Determine Oxygen, Hydrogen, and Nitrogen in Inorganic Samples |
| Analisi RAMAN bulk | RAMAN bulk analysis |
| Analisi SEM/EDS | Scanning electron microscopy analysis with X-ray detector |
| Analisi tomografica - Computed Tomography scan | Computed tomography 3D scan |
| Analisi XRD | X-ray diffraction analysis |
| API RP 5L2 Appendix F | Hydraulic blistering |
| API RP 5L7 | Recommended Practices for Unprimed Internal Fusion Bonded Epoxy Coating of Line Pipe - Particle size |
| API RP 5L7 Appendix 1 | Recommended Practices for Unprimed Internal Fusion Bonded Epoxy Coating of Line Pipe - Infrared spectroscopy |
| API RP 5L7 Appendix 11 | Cathodic disbondment |
| API RP 5L7 Appendix 13 | Flexibility |
| API RP 5L7 Appendix 16 | Hot water soak |
| API RP 5L7 Appendix 2 | Recommended Practices for Unprimed Internal Fusion Bonded Epoxy Coating of Line Pipe - Specific gravity |
| API RP 5L7 Appendix 4 | Recommended Practices for Unprimed Internal Fusion Bonded Epoxy Coating of Line Pipe - Gel time |
| API RP 5L7 Appendix 5 | Recommended Practices for Unprimed Internal Fusion Bonded Epoxy Coating of Line Pipe - Glass transition and heat of reaction determination |
| API RP 5L7 Appendix 7 | Recommended Practices for Unprimed Internal Fusion Bonded Epoxy Coating of Line Pipe - Total volatile content |
| AS 1580.408.2 | Adhesion - Knife test |
| ASTM A1038 | Metallic coatings - Portable Hardness Testing by the Ultrasonic Contact Impedance Method |
| ASTM A262 Practice B | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels - Ferric Sulfate-Sulfuric Acid Test for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels (Sections 14 to 25, inclusive) |
| ASTM A262 Practice C | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels - Nitric Acid Test for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels (Sections 26 to 36, inclusive) |
| ASTM A380 / A380M par.7.3.4 | Stainless steel - Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems - Ferroxyl Test for Free Iron |
| ASTM A90 / A90M | Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings |
| ASTM A967 par.18 | Standard Specification for Chemical Passivation treatments for Stainless Steel Parts - Practice E—Potassium Ferricyanide-Nitric Acid Test |
| ASTM B117 | Organic and inorganic coatings on metallic substrate - Standard Practice for Operating Salt Spray (Fog) Apparatus |
| ASTM B117 and ASTM D5894 | Painted metal - Salt spray and Cyclic Salt Fog-UV Exposure |
| ASTM B137 | Anodically Coated Aluminum - Measurement of Coating Mass Per Unit Area |
| ASTM B244 | Thickness of Nonconductive Coatings on Nonmagnetic Basis Metals |
| ASTM B487 | Coating - Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section |
| ASTM B504 | Metallic Coatings - Measurement of Thickness by the Coulometric Method |
| ASTM B764 | Metallic coatings - Simultaneous Thickness and Electrode Potential Determination of Individual Layers in Multilayer Nickel Deposit (STEP Test) |
| ASTM C1057 | Standard Practice for Determination of Skin Contact Temperature from Heated Surfaces Using a Mathematical Model and Thermesthesiometer |
| ASTM C1371 | Standard Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers |
| ASTM C1549 | Standard Test Method for Determination of Solar Reflectance Near Ambient Temperature Using a Portable Solar Reflectometer |
| ASTM C177 | Thermal insulation - Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus |
| ASTM C1784 | Building materials - Using a Heat Flow Meter Apparatus for Measuring Thermal Storage Properties of Phase Change Materials and Products |
| ASTM C372 | Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method |
| ASTM C501 | Ceramics - Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber Abraser |
| ASTM C518 | Building materials and products - Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
| ASTM C531 | Standard Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes |
| ASTM C539 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Ceramic Whiteware Materials by Interferometric Method |
| ASTM C633 | Adhesion or Cohesion Strength of Thermal Spray Coatings |
| ASTM C744 | Prefaced Concrete and Calcium Silicate Masonry Units - Abrasion resistance |
| ASTM C824 | Standard Practice for Specimen Preparation for Determination of Linear Thermal Expansion of Vitreous Glass Enamels and Glass Enamel Frits by Dilatometer Method |
| ASTM C832 | Standard Test Method of Measuring Thermal Expansion and Creep of Refractories Under Load |
| ASTM D 3763 | Plastics - High Speed Puncture Properties of Plastics Using Load and Displacement Sensors |
| ASTM D 6304 | Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration |
| ASTM D1000 21÷27 | Thickness |
| ASTM D1000 46÷53 | Adhesion strength |
| ASTM D1002 | Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal) |
| ASTM D1003 | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM D1004 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D1044 | Plastics - Resistance of Transparent Plastics to Surface abrasion by the Taber Abraser |
| ASTM D1084 Method B | Adhesives - Standard Test Methods for Viscosity of Adhesives |
| ASTM D1148 | Rubber - Discoloration from Ultraviolet (UV) or UV/Visible Radiation and Heat Exposure of Light-Colored Surfaces |
| ASTM D1149 | Rubber and Elastomers - Cracking in an Ozone Controlled Environment |
| ASTM D1193 | Standard Specification for Reagent Water |
| ASTM D1200 | Paints and varnishes - Viscosity by Ford Viscosity Cup |
| ASTM D1238 | Plastics - Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D1475 | Standard Test Method for Density of Liquid Coatings, Inks, and Related Products |
| ASTM D149 Method A | Solid Electrical Insulating Materials - Dielectric Breakdown Voltage and Dielectric Strength at Commercial Power Frequencies |
| ASTM D150 | Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation |
| ASTM D1525 | Plastics - Vicat Softening Temperature of Plastics |
| ASTM D1599 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D1621 | Rigid Cellular Plastics - Compressive Properties |
| ASTM D1622 | Rigid Cellular Plastics - Apparent Density |
| ASTM D1640/D1640M | Standard Test Methods for Drying, Curing, or Film Formation of Organic Coatings |
| ASTM D1653 Method B | Organic Coating Films - Standard Test Methods for Water Vapor Transmission |
| ASTM D1654 | Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments |
| ASTM D1693 | Plastics - Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D1729 | Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D1735 | Water Resistance of Coatings Using Water Fog Apparatus |
| ASTM D1748 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM D1781 | Adhesives - Climbing Drum Peel |
| ASTM D1849 | Standard Test Method for Package Stability of Paint |
| ASTM D1921 | Plastic Materials - Particle Size (Sieve Analysis) |
| ASTM D2000 | Rubber Products in Automotive Applications |
| ASTM D217 | Lubricating Grease - Cone Penetration |
| ASTM D2240 | Rubber Property - Durometer Hardness |
| ASTM D2244 | Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM D2247 | Paints and Varnishes - Water Resistance of Coatings in 100 Relative Humidity |
| ASTM D2304 | Thermal Endurance of Rigid Electrical Insulating Materials |
| ASTM D2344 | Polymer Matrix Composite Materials and Their Laminates - Short-Beam Strength |
| ASTM D2369 | Paint and varnishes - Volatile Content of Coatings |
| ASTM D2370 | Standard Test Method for Tensile Properties of Organic Coatings |
| ASTM D2372 | Standard Practice for Separation of Vehicle From Solvent-Reducible Paints |
| ASTM D2454 | Determining the Effect of Overbaking on Organic Coatings |
| ASTM D2457 | Specular Gloss of Plastic Films and Solid Plastics |
| ASTM D2485 | Paint and varnish - Evaluating Coatings For High Temperature Service |
| ASTM D2486 | Standard Test Methods for Scrub Resistance of Wall Paints |
| ASTM D256 | Plastics - Izod -notched impact strength |
| ASTM D2565 | Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications |
| ASTM D257 | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ASTM D2583 | Reinforced and nonreinforced rigid plastics - Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor |
| ASTM D2584 | Reinforced Resins - Ignition Loss of Cured Reinforced Resins |
| ASTM D2621 | Paints and varnishes - Infrared Identification of Vehicle Solids From Solvent-Reducible Paints |
| ASTM D2697 | Paint and varnishes - Volume Nonvolatile Matter in Clear or Pigmented Coatings |
| ASTM D2732 | Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting |
| ASTM D2739 | Adhesives - Volume Resistivity of Conductive Adhesives |
| ASTM D2794 | Resistance of Organic Coatings to the Effects of rapid deformation (Impact) |
| ASTM D2805 | Paints and Varnishes - Hiding Power of Paints by Reflectometry |
| ASTM D2842 | Standard Test Method for Water Absorption of Rigid Cellular Plastics |
| ASTM D297 par. 16.3 | Rubber Products - Density - Hydrostatic method |
| ASTM D2974 | Standard Test Methods for Determining the Water (Moisture) Content, Ash Content, and Organic Material of Peat and Other Organic Soils |
| ASTM D2990 | Plastics - Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics |
| ASTM D3039 | Composites - Tensile Properties of Polymer Matrix Composite Materials |
| ASTM D3167 | Standard Test Method for Floating Roller Peel Resistance of Adhesives |
| ASTM D3170 / D3170M | Coatings - Standard Test Method for Chipping Resistance of Coatings |
| ASTM D3171 | Constituent Content of Composite Materials |
| ASTM D3330 / D3330M | Pressure Sensitive Tape - Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape |
| ASTM D3350 par. 10.1.9 | Polyethylene Plastics Pipe and Fittings Materials - Thermal stability |
| ASTM D3359 | Paints and Varnishes - Adhesion by Tape Test |
| ASTM D3363 | Film Hardness by Pencil Test |
| ASTM D3418 | Polymers - Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry |
| ASTM D3518 | Composites - In-Plane Shear Response of Polymer Matrix Composite Materials by Tensile Test of a ±45° Laminate |
| ASTM D3787 | Standard Test Method for Bursting Strength of Textiles—Constant-Rate-of-Traverse (CRT) Ball Burst Test |
| ASTM D3835 | Plastics - Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer |
| ASTM D3884 | Textile Fabrics - Abrasion Resistance |
| ASTM D3895 | Polymers - Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
| ASTM D395 | Rubber Property - Compression Set - Costant deflection in air |
| ASTM D3985 | Plastics - Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D4017 | Standard Test Method for Water in Paints and Paint Materials by Karl Fischer Method |
| ASTM D4060 | Paints and varnishes - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
| ASTM D4065 | Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures |
| ASTM D412 | Vulcanized Rubber and Thermoplastic Elastomers - Tension |
| ASTM D4145 | Paints and varnishes - Standard Test Method for Coating Flexibility of Prepainted Sheet |
| ASTM D4213 | Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss |
| ASTM D4228 | Qualification of Coating Applicators for Application of Coatings to Steel Surfaces |
| ASTM D4274 | Polyurethane Raw Materials - Hydroxyl Numbers of Polyols |
| ASTM D4289 | Lubricating Greases and Fluids - Elastomer Compatibility |
| ASTM D429 Method B | Rubber Property - Adhesion to Rigid Substrates - Stripping test |
| ASTM D4329 | Plastics - Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics |
| ASTM D4332 | Containers, Packages, or Packaging - Conditioning enviroment |
| ASTM D4366 | Hardness of Organic Coatings by Pendulum Damping Tests |
| ASTM D4414 | Standard Practice for Measurement of Wet Film Thickness by Notch Gages |
| ASTM D445 | Petroleum products - Kinematic Viscosity of Transparent and Opaque Liquids |
| ASTM D4541 | Paints and varnishes - Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D4585 / D4585M | Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation |
| ASTM D4587 | Paints and Varnishes - Fluorescent UV-Condensation Exposures |
| ASTM D4595 | Geotextiles fibers - Tensile Properties of Geotextiles by the Wide-Width Strip Method |
| ASTM D4672 | Polyurethane Raw Materials - Water Content |
| ASTM D471 | Rubbers - Effect of Liquids |
| ASTM D4752 | Standard Practice for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub |
| ASTM D4812 | Unnotched Cantilever Beam Impact Resistance of Plastics |
| ASTM D4889 | Polyurethane Raw Materials - Viscosity of Crude or Modified Isocyanates |
| ASTM D4940 | Conductimetric Analysis of Water Soluble Ionic Contamination of Blast Cleaning Abrasives |
| ASTM D4972 | Standard Test Methods for pH of Soils |
| ASTM D4991 | Empty Rigid Containers - Leakage Testing of Empty Rigid Containers by Vacuum Method |
| ASTM D5026 | Plastics - Dynamic Mechanical Properties: In Tension |
| ASTM D5155 | Polyurethane Raw Materials - Isocyanate Content of Aromatic Isocyanates |
| ASTM D5162 | Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates |
| ASTM D520 | Standard Specification for Zinc Dust Pigment |
| ASTM D521 | Chemical Analysis of Zinc Dust |
| ASTM D522 | Paints and varnishes - Mandrel Bend Test of Attached Organic Coatings |
| ASTM D523 | Specular gloss |
| ASTM D5381 | Pigments and Extenders - X-Ray Fluorescence (XRF) Spectroscopy of Pigments and Extenders |
| ASTM D5402 | Solvent Resistance of Organic Coatings Using Solvent Rubs |
| ASTM D542 | Plastics - Standard Test Method for Index of Refraction of Transparent Organic Plastics |
| ASTM D5420 | Flat Rigid Plastic Specimen - Impact Resistance by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| ASTM D562 | Standard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer |
| ASTM D5656 | Standard Test Method for Thick-Adherend Metal Lap-Shear Joints for Determination of the Stress-Strain Behavior of Adhesives in Shear by Tension Loading |
| ASTM D570 | Plastics - Water Absorption |
| ASTM D575 | Rubber - Rubber Properties in Compression |
| ASTM D5868 | Standard Test Method for Lap Shear Adhesion for Fiber Reinforced Plastic (FRP) Bonding |
| ASTM D5894 | Standard Practice for Cyclic Salt Fog-UV Exposure of Painted Metal, (Alternating Exposures in a Fog-Dry Cabinet and a UV-Condensation Cabinet) |
| ASTM D6099 | Polyurethane Raw Materials - Acidity in Moderate to High Acidity Aromatic Isocyanates |
| ASTM D610 | Evaluating Degree of Rusting on Painted Steel Surfaces |
| ASTM D6110 | Charpy Impact Resistance of Notched Specimens of Plastics |
| ASTM D6184 | Standard Test Method for Oil Separation from Lubricating Grease (Conical Sieve Method) |
| ASTM D6226 | Rigid Cellular Plastics - Standard Test Method for Open Cell Content |
| ASTM D624 | Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers |
| ASTM D635 | Rate of Burning and-or Extent and Time of Burning of Plastics in a Horizontal Position |
| ASTM D638 | Plastics - Tensile Properties |
| ASTM D642 | Shipping Containers, Components, and Unit Loads - Compressive Resistance |
| ASTM D648 | Plastics - Deflection Temperature Under Flexural Load in the Edgewise Position |
| ASTM D6580 | Determination of Metallic Zinc Content in Both Zinc Dust Pigment and in Cured Films of Zinc-Rich Coatings |
| ASTM D6641 | Composite - Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture |
| ASTM D6677 | Adhesion by Knife |
| ASTM D6695 | Paint and varnish - Xenon-Arc Exposures of Paint and Related Coatings |
| ASTM D6797 | Fabrics - Standard Test Method for Bursting Strength of Fabrics Constant-Rate-of-Extension (CRE) Ball Burst Test |
| ASTM D6886 | Standard Test Method for Determination of the Weight Percent Individual Volatile Organic Compounds in Waterborne Air-Dry Coatings by Gas Chromatography |
| ASTM D6943 | Protective Coatings and Linings - Immersion Testing |
| ASTM D6944 Method A | Standard Practice for Determining the Resistance of Cured Coatings to Thermal Cycling - FREEZE-THAW-IMMERSION |
| ASTM D695 | Compressive Properties of Rigid Plastics |
| ASTM D696 | Plastics - Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C with a Vitreous Silica Dilatometer |
| ASTM D7073 | Standard Guide for Application and Evaluation of Brush and Roller Applied Paint Films |
| ASTM D7091 | Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D714 | Standard Test Method for Evaluating Degree of Blistering of Paints |
| ASTM D7191 | Plastics - Standard Test Method for Determination of Moisture in Plastics by Relative Humidity Sensor |
| ASTM D7205 / D7205M | Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars |
| ASTM D7291/D7291M | Standard Test Method for Through-Thickness “Flatwise” Tensile Strength and Elastic Modulus of a Fiber-Reinforced Polymer Matrix Composite Material |
| ASTM D732 | Plastics - Standard Test Method for Shear Strength of Plastics by Punch Tool |
| ASTM D746 | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact |
| ASTM D751 par.18 | Standard Test Methods for Coated Fabrics - Bursting strength |
| ASTM D751 par.22 | Coated Fabrics - Puncture resistance |
| ASTM D7869 | Coatings - Xenon Arc Exposure Test with Enhanced Light and Water Exposure |
| ASTM D790 | Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D792 | Plastics - Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D8133 Method B | Plastics - Determination of Low Level Phthalates in Poly(Vinyl Chloride) Plastics by Solvent Extraction—Gas Chromatography-Mass Spectrometry |
| ASTM D817 par. 7-8-9 | Ash test |
| ASTM D870 | Coating - Standard Practice for Testing Water Resistance of Coatings Using Water Immersion |
| ASTM D882 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting |
| ASTM D942 | Lubricating Greases - Oxidation Stability of by the Oxygen Pressure Vessel Method |
| ASTM D953 | Plastics - Pin-Bearing Strength |
| ASTM D968 | Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive |
| ASTM D991 | Rubber vulcanized or thermoplastic - Volume Resistivity |
| ASTM E10 | Metallic Materials - Brinell Hardness of Metallic Materials |
| ASTM E1019 | Metals - Chemical analysis of Carbon and Sulfur |
| ASTM E1131 | Standard Test Method for Compositional Analysis by Thermogravimetry |
| ASTM E1252 | General Techniques for Obtaining Infrared Spectra for Qualitative Analysis |
| ASTM E1269 | Specific Heat Capacity by Differential Scanning Calorimetry |
| ASTM E1356 | Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry |
| ASTM E1461 | Plastics - Thermal Diffusivity by the Flash Method |
| ASTM E1476 par. 7.1 | Metals Identification, Grade Verification and Sorting - X-ray fluorescence spectrometry |
| ASTM E1530 | Evaluating the Resistance to Thermal Transmission by the Guarded Heat Flow Meter Technique |
| ASTM E1545 | Standard Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis |
| ASTM E1578 | Standard Guide for Laboratory Informatics |
| ASTM E1640 | Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis |
| ASTM E168 | General Techniques of Infrared Quantitative Analysis |
| ASTM E179 | Standard Guide for Selection of Geometric Conditions for Measurement of Reflection and Transmission Properties of Materials |
| ASTM E1824 | Standard Test Method for Assignment of a Glass Transition Temperature Using Thermomechanical Analysis: Tension Method |
| ASTM E1920 | Standard Guide for Metallographic Preparation of Thermal Sprayed Coatings |
| ASTM E1933 | Measuring and Compensating for Emissivity Using Infrared Imaging Radiometers |
| ASTM E2092 | Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis |
| ASTM E2109 | Thermal spray coatings - Determining Area Percentage Porosity |
| ASTM E228 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer |
| ASTM E2347-21 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis |
| ASTM E2602-22 | Standard Test Methods for Assignment of the Glass Transition Temperature by Modulated Temperature Differential Scanning Calorimetry |
| ASTM E2716-23 | Standard Test Method for Determining Specific Heat Capacity by Modulated Temperature Differential Scanning Calorimetry |
| ASTM E2769 | Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading |
| ASTM E28 | Plastics - Softening Point of Resins Derived from Pine Chemicals and Hydrocarbons, by Ring-and-Ball Apparatus |
| ASTM E2937 | Paint and varnish - Infrared Spectroscopy in Paint Examinations |
| ASTM E3 + ASTM E407 | Metallic materials - Micrographic examination |
| ASTM E3061 | Aluminium Alloys - Analysis of Aluminum by Inductively Coupled Plasma Atomic Emission Spectrometry |
| ASTM E308 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM E350 | Metals - Carbon steel low-alloy steels - Chemical analysis of Silicon and Manganese |
| ASTM E376 | Measuring Coating Thickness by Magnetic-Field or Eddy Current (Electromagnetic) Testing Methods |
| ASTM E384 | Standard Test Method for Microindentation Hardness of Materials |
| ASTM E398 | Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement |
| ASTM E430 | Paint and varnish - Measurement of Gloss of High-Gloss Surfaces by Abridged Goniophotometry (DOI) |
| ASTM E573 | Internal Reflection Spectroscopy (ATR) |
| ASTM E793 | Enthalpies of Fusion and Crystallization by Differential Scanning Calorimetry |
| ASTM E797 / E797M | Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method |
| ASTM E831 | Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis |
| ASTM E855 | Bend Testing of Metallic Flat Materials for Spring Applications Involving Static Loading |
| ASTM E903 | Plastic materials - Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres |
| ASTM E96 / E96M | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM E967 | Temperature Calibration of Differential Scanning Calorimeters and Differential Thermal Analyzers |
| ASTM F1306 | Standard Test Method for Slow Rate Penetration Resistance of Flexible Barrier Films and Laminates |
| ASTM F1624 | Standard Test Method for Measurement of Hydrogen Embrittlement Threshold in Steel by the Incremental Step Loading Technique |
| ASTM F1978 | Thermal spray coatings - Standard Test Method for Measuring Abrasion Resistance of Metallic Thermal Spray Coatings by Using the Taber Abraser |
| ASTM F2625 | Standard Test Method for Measurement of Enthalpy of Fusion, Percent Crystallinity, and Melting Point of Ultra-High-Molecular Weight Polyethylene by Means of Differential Scanning Calorimetry |
| ASTM F3039 | Nonporous Packaging or Flexible Barrier Materials - Detecting Leaks in Nonporous Packaging or Flexible Barrier Materials by Dye Penetration |
| ASTM F433 | Standard Practice for Evaluating Thermal Conductivity of Gasket Materials |
| ASTM F510 / F510M | Resistance to Abrasion of Resilient Floor Coverings Using an Abrader with a Grit Feed Method |
| ASTM G 154 | Nonmetallic Materials - Irradiance by operating Fluorescent Ultraviolet (UV) Lamp Apparatus |
| ASTM G14 | Pipeline Coatings - Impact Resistance by falling weight |
| ASTM G155 | Non-metallic materials - Xenon arc light exposure |
| ASTM G17 | Penetration Resistance of Pipeline Coatings (Blunt Rod) |
| ASTM G187 | Standard Test Method for Measurement of Soil Resistivity Using the Two-Electrode Soil Box Method |
| ASTM G20 | Chemical Resistance of Pipeline Coatings |
| ASTM G42 | Rubber vulcanized or thermoplastic - Cathodic Disbonding |
| ASTM G59 | Metals - Potentiodynamic Polarization Resistance Measurements |
| ASTM G62 | Holiday Detection in Pipeline Coatings |
| ASTM G65 | Determination of Abrasion Using the Dry Sand-Rubber Wheel Apparatus |
| ASTM G76 | Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets |
| ASTM G8 | Standard Test Methods for Cathodic Disbonding of Pipeline Coatings |
| ASTM G85 | Paint and varnish - Modified Salt Spray (Fog) Testing |
| ASTM G9 | Water Penetration into Pipeline Coatings |
| ASTM G95 | Cathodic Disbondment Test of Pipeline Coatings (Attached Cell Method) |
| AWWA C203 | COAL-TAR PROTECTIVE COATINGS AND LININGS FOR STEEL WATER PIPES |
| AWWA C209 | Tape Coatings for Steel Water Pipe and Fittings |
| AWWA C210 | Liquid-Epoxy Coatings and Linings for Steel Water Pipe and Fittings |
| AWWA C213 | Fusion-Bonded Epoxy Coatings and Linings for Steel Water Pipe and Fittings |
| AWWA C213 par.5.2.2.3 | Fusion-Bonded Epoxy Coatings and Linings for Steel Water Pipe and Fittings - Bendability |
| AWWA C213 par.5.2.2.4 | Fusion-Bonded Epoxy Coatings and Linings for Steel Water Pipe and Fittings - Shear adhesion |
| AWWA C213 par.5.2.2.7 | Fusion-Bonded Epoxy Coatings and Linings for Steel Water Pipe and Fittings - Hot water soak |
| AWWA C214 | Tape Coatings for Steel Water Pipe |
| AWWA C215 | Extruded Polyolefin Coatings for the Exterior of Steel Water Pipelines |
| AWWA C216 | Heat-Shrinkable Cross-Linked Polyolefin Coatings for Steel Water Pipe and Fittings |
| AWWA C217 | Microcrystalline Wax and Petrolatum Tape Coating Systems for Steel Waer Pipe and Fittings |
| AWWA C218 | Liquid Coating for Aboveground Steel Water Pipelines and Fittings |
| AWWA C222 | Polyurethane Coatings for the Interior and Exterior of Steel Water Pipe and Fittings |
| AWWA C224 | Nylon-11 Based Polyamide Coating System for the Interior and Exterior of Steel Water Pipe, Connections, Fittings and Special Sections |
| AWWA C225 | Fused Polyolefin Coating System for the Exterior of Steel Water Pipelines |
| AWWA C229 | Fusion-Bonded Polyethylene Coatings for Steel Water Pipe and Fittings |
| AWWA C550 | Protective Interior Coatings for Valves and Hydrants |
| AWWA C605 | Underground Installation of Polyvinyl Chloride (PVC) and Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe and Fittings |
| AWWA C620 | Spray-Applied In-Place Epoxy Lining of Water Pipelines, 3 In. (75 mm) and Larger |
| AWWA C900 | Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 In. - 60 In. (100 mm - 1,5000 mm) |
| AWWA C901 | Polyethylene (PE) Pressure Pipe and Tubing, 1-2 In. (13 mm) - 3 In. (76 mm), for Water Service |
| AWWA C903 | Polyethylene-Aluminum-Polyethylene (PE-AL-PE) Composite Pressure Pipe, 12 mm(1-2 In.) - 51 mm (2 In.), for Water Service |
| AWWA C904 | Cross-Linked Polyethylene (PEX) Pressure Pipe, 1-2 In. (12 mm) - 3 In. (76 mm), for Water Service |
| AWWA C906 | Polyethylene (PE) Pressure Pipe and Fittings, 4 In. Through 65 In (100 mm Through 1,650 mm) for Waterworks |
| AWWA C907 | Injection-Molded Polyvinyl Chloride (PVC) Pressure Fittings, 4 In. - 24 In. (100 mm Through 300 mm) for Water, Wastewater and Reclaimed Water Services |
| AWWA C909 | Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe, 4 In. - 24 In. (100 mm - 600 mm) for Water, Wastewater, and Reclaimed Water Service |
| AWWA C950 | Fiberglass Pressure Pipe |
| BA QA 101P | Viscosity Measurement |
| BART Test | BART Test Semi quantitative |
| BMW AA-0026 | Automotive parts - Aging resistance test |
| BMW AA-0054 | Resistance of Coatings to Car-wash Machines |
| BMW AA-0055 | Chemical resistance test of surfaces |
| BMW AA-0079 | Multi impact stone chip resistance |
| BMW AA-0101 | Reflectometer Value (Gloss) |
| BMW AA-0129 | CASS-Test |
| BMW AA-0136 | Steam Jet Test |
| BMW AA-0161 | Color measurement |
| BMW AA-0180 | Cross hatch testing |
| BMW AA-0213 | Condensation Water Constant Atmosphere Test |
| BMW AA-0224 | Cyclic corrosion |
| BMW AA-0254 | Coating thickness |
| BMW AA-0257 | Paint and varnishes - Measurement of structure and gloss on painted surfaces |
| BMW AA-0324 | Saltspray-Test |
| BMW AA-0340 | Scalpel cut on CFK-parts with clearcoats |
| BMW AA-0403 | Paint and varnishes - Visual Color Comparison and Metamerism Test coated test panels |
| BMW GS 97034-9 | Scratch test |
| BS 3900 E2 | Part E2: Scratch test |
| BS 3900-E3 | Part E3: Impact (falling weight) resistance |
| BS 3900-E7 | Impact - Falling ball test |
| BSI PAS 27 par. 9.1.12 escl. F.4.7. | Unplasticized PVC-A pipes and bends for water under pressure - Resistance to three-point bend when notched |
| CEI EN 60529 | Degrees of protection of the enclosures - IP classification |
| CEI EN IEC 60079-0 par.26.10 | Explosive atmospheres - Part 0: Equipment - General requirements - Resistance to light |
| CEI EN IEC 60079-0 par.26.13 | Explosive atmospheres - Part 0: Equipment – General requirements - Surface resistance test of parts of enclosures of non-metallic materials |
| CEI EN IEC 60079-0 par.26.17 | Explosive atmospheres - Part 0: Equipment - General requirements - Transferred charge test |
| CEI EN IEC 60079-0 par.7.4.2 | Explosive atmospheres - Part 0: Equipment - General requirements - Avoidance of a build-up of electrostatic charge for Group I or Group II |
| CEN/TS 13130-13 | Determination of 2,2-bis(4-hydroxyphenyl)propane (Bisphenol A) in food simulants |
| CHN | CHN elemental analysis |
| Cicli di pressione | Pressure cycles |
| CNH ENS0103 | Component cleanliness and acceptance criteria |
| CNH ENS0310 p.10.2.3 | Environmental Test Specification - Particle impacts |
| CNH MTM0108 | Chemical resistance |
| CNH MTM0122 | Chip resistance |
| CNH MTM0124 | Flexibility test |
| CNH MTM0140 | Dry film thickness |
| CNR IRSA 16 Q64 Vol 3 | Analytical methods for sludges - Chrome (VI) – Method CNR IRSA 16 Q 64 Vol 3 1986 |
| CNR IRSA Q24 VOL3 17 | Cianuri totali (mg-kg) |
| CSA Z245.20 par.12.1 | Plant-applied external coatings for steel pipe - Cure time of epoxy powder |
| CSA Z245.20 par.12.10 | Plant-applied external coatings for steel pipe - Cross-section and interface porosity |
| CSA Z245.20 par.12.11 | Plant-applied external coatings for steel pipe - Flexibility of the coating |
| CSA Z245.20 par.12.12 | Plant-applied external coatings for steel pipe - Impact resistance of the coating |
| CSA Z245.20 par.12.13 | Plant-applied external fusion bond epoxy coatign for steel pipe - Strained Coating Cathodic Disbondment |
| CSA Z245.20 par.12.14 | Plant-applied external coatings for steel pipe - Adhesion of the coating |
| CSA Z245.20 par.12.16 | Plant-applied external coatings for steel pipe - Surface roughness for anti-slip overcoat systems |
| CSA Z245.20 par.12.2 | Plant-applied external coatings for steel pipe - Gel time of epoxy powder |
| CSA Z245.20 par.12.4 | Plant-applied external coatings for steel pipe - Moisture of the epoxy powder |
| CSA Z245.20 par.12.5 | Plant-applied external coatings for steel pipe - Particle size |
| CSA Z245.20 par.12.6 | Plant-applied external fusion bond epoxy coatign for steel pipe - Density |
| CSA Z245.20 par.12.7 | Plant-applied external coatings for steel pipe - Thermal characteristics of the epoxy powder and coating |
| CSA Z245.20 par.12.8 | Fusion bond epoxy coating for steel - Cathodic disbondment of the coating |
| CSA Z245.20 par.12.9 | Plant-applied external coatings for steel pipe - Interface contamination of the coating |
| CSA Z245.20:2018 par.12.15 | Gouge resistance of coating |
| CSA Z245.21 par.12.3 | Plant-applied external polyethylene coating for steel pipe - Cathodic disbonding of the coating |
| CSS PdP-SD2010 rev.0 del 26/10/20 | Apparent saturated density in water after immersion in water at high pressure |
| D.M. n°174/2004 | Prove potabilità |
| DBL 1232 par.6.3, Table B.1 - Ash content | Ash content |
| DBL 5416 par.12.4 | Cross cut with adhesive tape application and removal |
| DBL 5416 par.12.6 | Steam jet test |
| DBL 5416 par.12.7 Method 1 | Climatic cycle test |
| DBL 5490 - Ash content | Ash content |
| DBL 5555 par.8 | Finished parts and semi-finished products - Hot-storage behaviour of plastics |
| DEF STAN 05-133 Part 1, Clause 6.11 | Tolerance to sagging |
| DEF STAN 05-133 Part 1, Clause 8.2 | Resistance to immersion in artificial seawater |
| DEF STAN 05-133 Part 1, Clause 8.3 | Resistance to liquid fuel |
| DEF STAN 80-97 Annex B | Resistance to Aviation Fuels |
| Definito dal cliente | Pressure cycles - Fatigue test |
| Definito dal cliente | Thermal cycle / Cyclic ageing |
| DIN 30670-1 Annex B | Polyethylene coatings on steel pipes and fittings - Degree of cure of the epoxy resin layer |
| DIN 30670-1 Annex C | Polyethylene coatings on steel pipes and fittings - Cathodic disbondment (CD test) |
| DIN 30670-1 Annex D | Polyethylene coatings on steel pipes and fittings - Peel strength |
| DIN 30670-1 Annex E | Polyethylene coatings on steel pipes and fittings - Continuity (holiday detection) |
| DIN 30670-1 Annex F | Polyethylene coatings on steel pipes and fittings - Allungamento a rottura +23°C |
| DIN 30670-1 Annex G | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - Impact resistance and low temperature impact resistance |
| DIN 30670-1 Annex H | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - Indentation resistance |
| DIN 30670-1 Annex I | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - Specific electrical coating resistance |
| DIN 30670-1 Annex J | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - UV resistance |
| DIN 30670-1 Annex K | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - Thermal ageing |
| DIN 30670-2 Annex B | Polyethylene coatings on steel pipes and fittings - Degree of cure of the epoxy resin layer |
| DIN 30670-2 Annex C | Polyethylene coatings on steel pipes and fittings - Cathodic disbondment (CD test) |
| DIN 30670-2 Annex D | Polyethylene coatings on steel pipes and fittings - Peel strength |
| DIN 30670-2 Annex E | Polyethylene coatings on steel pipes and fittings - Continuity (holiday detection) |
| DIN 30670-2 Annex F | Polyethylene coatings on steel pipes and fittings - Allungamento a rottura +23°C |
| DIN 30670-2 Annex G | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - Impact resistance and low temperature impact resistance |
| DIN 30670-2 Annex H | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - Indentation resistance |
| DIN 30670-2 Annex I | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - Specific electrical coating resistance |
| DIN 30670-2 Annex J | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - UV resistance |
| DIN 30670-2 Annex K | Polyethylene coatings on steel pipes and fittings - Part 1: Requirements and testings of factory-applied extruded coatings - Thermal ageing |
| DIN 30671 par. 5.6 | Thermoset plastic coatings for buried steel pipes - Flexibility |
| DIN 30672-1 | Field coating materials for corrosion protection of buried pipelines - Part 1: Requirements and product testings |
| DIN 30672-2 | Field coating materials for corrosion protection of buried pipelines - Part 2: Application and quality control on site |
| DIN 30672-2 Appendix C | Field coating materials for corrosion protection of buried pipelines - Part 2: Application and quality control on site - Resistance to peeling |
| DIN 30678 Annex I | Polypropylene coatings on steel pipes and fittings - Requirements and testing - Indentation resistance |
| DIN 40050-9 | Road Veichles - Degrees of protection (IP code) |
| DIN 50018 | Corrosion testing - Testing in a saturated atmosphere in the presence of sulfur dioxide |
| DIN 51045-1 | Determination of the thermal expansion of solids - Part 1: Basic rules |
| DIN 51045-2 | Determination of linear thermal expansion of solids - Part 2: Testing of fired fine ceramic materials using the dilatometer method |
| DIN 51045-3 | Determination of linear thermal expansion of solids - Part 3: Testing of non-fired fine ceramic materials using the dilatometer method |
| DIN 51045-4 | Determination of linear change of solids by thermal effect using the dilatometer method - Part 4: Testing of fired heavy ceramic materials |
| DIN 51045-5 | Determination of linear change of solids by thermal effect using the dilatometer method - Part 5: Testing of non-fired heavy ceramic materials |
| DIN 51739 | Testing of solid fuels - Determination of the dilatation of coal |
| DIN 51802 | Testing Lubricating Greases For Their Corrosion-Inhibiting Properties - Emcor test |
| DIN 51909 | Solid matters - Testing of carbon materials - Determination of coefficient of linear thermal expansion solid matters |
| DIN 53100 Annex F | Metallic coatings - Electroplated coatings of nickel plus chromium and of copper plus nickel plus chromium on plastics materials - glacial acetic acid test |
| DIN 53236-A | Colouring materials - Conditions of measurement and evaluation for the determination of colour differences for paint coatings, similar coatings and plastics |
| DIN 53380-3 | Plastics - Determination of gas trasmission rate - Part3: Oxygen-specific carrier gas method for testing of plastics films and plastics mouldings |
| DIN 53435 | Plastics - Impact test on dynstat test specimens |
| DIN 53491 | Testing of Plastics - Determination of the Refractive Index and Dispersion |
| DIN 53497 | Hot storage test on mouldings made of thermoplastic moulding materials without external mechanical stressing |
| DIN 53504 | Testing of rubber - Determination of tensile strength at break, tensile stress at yield, elongation at break and stress values in a tensile test |
| DIN 53512 | Rubbers - Determination The Rebound Resilience Of Rubber Using The Schob Pendulum |
| DIN 54345-1 | Testing of textiles - Electrostatic behaviour - Determination of electrical resistance |
| DIN 55635 | Paints and varnishes - Cyclic corrosion testing of coating systems on materials and components in automotive construction |
| DIN 75201 | Determination of the fogging characteristics of trim materials in the interior of automobiles |
| DIN 75220 | Ageing automotive components in solar simulation unit |
| DIN EN 16165 | Determination of slip resistance of pedestrian surfaces |
| DM 13/09/1999 SO n°185 GU n° 248 21/10/1999 Met IV.2 | Soluble chlorides and sulfates (mg-kg s.s.) |
| DM 21/03/1973 GU n° 104 20/04/1973 All IV Se1 | DM 21-03-1973 GU n° 104 20-04-1973 All IV Sez 1 + DM 26-04-1993 GU n° 162 13-07-1993 All III + DM 24-09-1996 gu N° 264 11-11-1996 + DM 28-03-2003 GU n°125 31-05-2003 + DM 22-12-2005 GU n° 37 14-02-2005 |
| DNVGL-RP-0416 | Corrosion protection for wind turbines |
| DOC. NO. KOC-P-004 Pt. 7 | TESTS FOR HEAT SHRINK SLEEVE - Soil stress (shear test |
| DVP 15.3 - Lifetime test Material aging | DVP 15.3 - Lifetime test Material aging |
| EN 10289 par.7.15 | Steel tubes and fittings for onshore and offshore pipelines - External liquid applied epoxy and epoxy-modified coatings - Infra-red scan obtained with a KBr standard disk |
| EN 10290 Annex A | Thickness of the coating |
| EN 10290 Annex B | Holiday detection |
| EN 10290 Annex C | External liquid applied polyurethane and polyurethane-modified coatings - Impact test |
| EN 10290 Annex D | Adhesion test - Resistance to removal |
| EN 10290 Annex E | Cathodic disbondment |
| EN 10290 Annex F | Steel tubes and fittings for onshore and offshore pipelines - External liquid applied polyurethane and polyurethane-modified coatings - Specific electrical insulation resistance test |
| EN 10290 Annex G | Adhesion test after immersion in tap water |
| EN 10290 Annex H | Indentation resistance |
| EN 10290 Annex J | Steel tubes and fittings for onshore and offshore pipelines - External liquid applied polyurethane and polyurethane-modified coatings - Thermal ageing |
| EN 10290 Annex K | Flexibility |
| EN 10290 par.7.17 | Elongation |
| EN 1090-2 Annex G.4 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures - Slip test (Short time) |
| EN 1090-2 Annex G.5 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures - Slip test (long time) |
| EN 1186-1 + EN 1186-3 | Migrazione globale in simulante alimentare acquoso per immersione totale |
| EN 1186-1 + EN 1186-5 | Migrazione globale in simulante alimentare acquoso mediante mediante l uso di una cella - Simulante C - Etanolo al 20 (v-v) - 10gg a 40°C |
| EN 1186-13 Method B | Migrazione globale in simulante E - Poli(ossido di 2,6-difenil-pfenilene) (MPPO) |
| EN 1297 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Method of artificial ageing by long term exposure to the combination of UV radiation, elevated temperature and water |
| EN 13071-1 par.6.6 | Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 1: General requirements - Weathering and ageing |
| EN 13501-1 | Fire classification of construction products and building elements - Single burning item (SBI) + Direct flame attack |
| EN 1401-1 par.13.2 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems - Minimum required marking of pipes |
| EN 1401-1 par.7.2 -1, -2, -3, -4, -5 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems - Dimensions of pipes |
| EN 1401-1 par.7.4.1.1 e 7.4.1.2 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems - Dimensions of socket and spigot |
| EN 1401-1 par.8.1.1.2 + ISO 3127 | Thermoplastics pipes - Determination of resistance to external blows — Round-the-clock method |
| EN 14901-1 | Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 1: Epoxy coating (heavy duty) |
| EN 1604 | Thermal insulating products for building applications - Dimensional stability under specified temperature and humidity conditions |
| EN 388 +A1 p.6.2 | Protective gloves against mechanical risks - Blade cut resistance |
| EN 60068-2-14 | Environmental testing - Change of temperature (thermal shock) |
| EN 6072 | Aerospace series - Metallic materials - Test methods - Constant amplitude fatigue testing |
| EN 658-3 | Advanced technical ceramics - Determination of flexural strength |
| EN 660-2 /A1 | Resilient floor coverings - Determination of wear resistance - Part 2: Frick-Taber test |
| EN 821-1 | Advanced technical ceramics - Monolithic ceramics - - Thermo-physical properties - Part 1: Determination of thermal expansion |
| EN 821-2 | Advanced technical ceramics - Monolithic ceramics - - Thermo-physical properties. Part 2: Determination of thermal diffusivity by the laser flash (or heat pulse) method |
| EN ISO 438-2 par. 10 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Resistance to surface wear |
| EN ISO 8130-2 | Rivestimento a polvere - Parte 2: Determinazione della densità mediante picnometro di confronto dei gas |
| EPA 3050B + EPA 6010D | Acid Digestion of Sediments, Sludges, and Soils - ICP method |
| EPA 3510C + EPA 8015D | GC analysis - Organic solvents mg-kg |
| EPA 3550C | Semi-volatile Organic Compounds - Semi-volatile organic compounds analisys using ultrasonic extraction |
| EPA 3550C + EPA8270D | IPA |
| EPA 5021A + EPA 8260D | Screening GC-MS - Static extraction |
| EPA 6010D | Restrizioni definite nell Allegato II del Reg.10-2011-UE e Reg. 752-2017 Parametro: Migrazione specifica Al, Ba, Co, Fe, Li, Mn, Ni, Cu e Zn |
| EPA 6010D + EPA 3051A | screening of the 8 metals mainly present |
| EPA 6020B + APAT CNR IRSA 4020 Man 29 | Water based liquids - Screening of the most present metals and anions within supply waters |
| EPA3550C + EPA8015D | Solventi clorurati mg-kg |
| EPA5021A + EPA8260C | Benzene mg-kg |
| ES805-001 Rev4 par.3.4 | Decorative chrome plating - Adhesion to metal substrate - Heat-quench (for high temperature applications) and reverse band saw cut tests |
| ES805-001 Rev4:2018 par.3.5 | Decorative chrome plating - Corrosion |
| ES805-07011 v13 par.6.4 | Humidity Resistance |
| ES805-34307 v4 par.6.5 | High temperature exhaust coatings - Corrosion resistance |
| ES805-34307 v4 par.6.6 | High temperature exhaust coatings - Thermal exposure with corrosion |
| ESPEC805-060 rev3 par.3 | Zinc-Nickel Plating - Adhesion after heat quench |
| ESPEC805-060 rev3 par.4 | Zinc-Nickel Plating - Corrosion performance |
| ETAG 004 par. 5.1.4.3.1 | External thermal insulation - Pull-through test on fixings |
| FAR 25.853 Appendix F Part IV | Heat Release Test |
| FAR 25.853 Appendix F, Part I, Par a1i | Fire reaction |
| FCA 50432/01 | Plastics - Determination of the stress cracking resistance |
| FCA 9.55254 par.2.5.4.2 | Resistance to hot dry |
| FCA 9.55254 par.2.5.4.3 | Resistance to heat stroke |
| FCA 9.55254 par.2.5.4.4 | Resistance to thermal cycle |
| FCA 9.55260/02 par.2.10 | Return after crushing |
| FCA 9.55260/02 par.2.5 | Compression rigidness |
| FCA 9.55260/02 par.2.6 | Density |
| FCA 9.55260/02 par.2.7 | Water absorption |
| FCA 9.55260/02 par.2.8 | Residual deformation |
| FCA 9.55260/02 par.2.9 | Odour |
| FCA 9.55727/02 par.2.4.9 | Shear resistance |
| FCA 9.55738 par.8.1.5 | Elastic adhesives for assembly - Immediate adhesion - peeling test |
| FCA 9.55842 par.2.13 | Accelerated aging to atmospheric agents |
| FCA 9.55842 par.2.15 | Aesthetic and operational finishing of plastic parts - Resistance to chemical aggressions |
| FCA 9.55842 par.2.4 | Thickness |
| FCA 9.55842 par.2.5.1 | Adhesion |
| FCA 9.55842 par.2.8.1 | Water immersion test |
| FCA 9.55842 par.2.9 | Damp heat resistance |
| FCA CS 00056 par.5.3.3 | Electronic devices - High Temperature Operating Edurance test (HTOE) |
| FCA CS 00056 par.5.3.4 | Electronic devices - Power Thermal Cycle Endurance test (PTCE) |
| FCA CS 00056 par.5.3.5 | Electronic devices - Thermal shock (TS) |
| FCA CS 00056 par.5.4.3 | Mechanical Vibration |
| FCA CS 00056 par.5.4.4 | Mechanical shock |
| FCA CS 00081 | Corrosion testing |
| FCA CS.13398 | Performance, Vehicle interior air quality material requirements |
| FCA LP 7M052 | Automotive fluids staining of plastics |
| FCA LP 7M060 | Abrasion test |
| FCA LP 7N022 | Cold impact performance |
| FCA LP.7M069 | Wear resistance of interior organic coatings |
| FCA LP-463DD-18-01 | Automotive plastics - Five finger scratch resistance test method |
| FCA LP-463DD-18-02 Method A | Automotive plastics - Method A: Scratch resistance |
| FCA LP-463DD-18-02 Method B | Automotive plastics - Method B: Mar resistance |
| FCA LP-463LB-13-01 | Heat aging |
| FCA LP-463PB-31-01 Met.A | Method A - Hot Immersion Test |
| FCA LP-463PB-31-01 Met.B | Method B - Spot Test |
| FCA LP-463PB-31-01 Met.C | Method C - Dip Test |
| FCA LP-463PB-31-01 Met.D | Method D - Suntan Lotion Test |
| FCA LP-463PB-31-01 Met.H | Resistance to various fluids - Method H |
| FCA LP-463PB-31-01 Met.J | Method J - Solvent Wipe Resistance - Rub Test |
| FCA LP-463PB-31-01 Met.K | Method K - Air Freshener Resistance |
| FCA LP-463PB-54-01 | Crock mar resistance |
| FCA MS 90102 | Organic coatings performance requirements for exterior |
| FCA MS 90102 Real automatic car wash | Real automatic car wash |
| FCA MS 90152 | Tape - Double coated pressure sensitive adhesive |
| FCA PF 90005 par.5.1 | Thermal shock |
| FCA PF 90005 par.5.2 | Thermal cycling |
| FCA PF 90005 par.5.3 | Dimensional stability |
| FCA PF 90005 par.5.5 | Humidity Resistance |
| FCA PF 90062 par.5.1.1 | Environmental Weathering - Xenon arc |
| FCA PF 90062 par.5.1.2 | Resistance to fluids |
| FCA PF 90062 par.5.12 | Dimensional Stability |
| FCA PF 90062 par.5.13 | Thermal shock |
| FCA PF 90062 par.5.14 | Thermal Cycling |
| FCA PF 90062 par.5.15 | Humidity resistance |
| FCA PF 90062 par.5.2 + FCA LP 7N022 | Cold impact performance |
| FCA PF 90062 par.6.1.1 | Aesthetic requirements |
| FCA PF 90122 par.5.1 | Temperature and humidity |
| FCA PF 90122 par.5.2 | Gravelometer |
| FCA PF 90122 par.7.1.6 | Insertion Force Testing Steps |
| FCA PF 90122 par.7.1.7 | Push-Through Force Testing Steps |
| FCA PF 90122 par.7.1.8 | Push-Out Force Testing Steps |
| FCA PF 90122 par.7.2 | Water column |
| FCA PF 90122 par.7.3 | Mud packing |
| FCA PF 90192 par.5.2.1 | Xenon exposure test |
| FCA PF 90192 par.5.3.1 | Fluid-chemical resistance test |
| FCA PF 90192 par.5.4.1 | Cleanability |
| FCA PF 90192 par.5.5.1 | Soil resistance test |
| FCA PF 90192 par.6.1.1 | Aesthetic requirements |
| FCA PF 90192 par.6.2.2 | Olfactory requirements |
| FCA PF 90192 par.6.2.3 | Fogging |
| FCA PF 90192 par.6.3.5 | Part identification and Marking |
| FCA PF 90192 par.6.3.6 | Traceability requirements |
| FCA PF 90192 par.8.1 | Flammability |
| FCA PF 90223 par.5.1.2 | Instrument Panel - Heat aging |
| FCA PF 90223 par.5.1.4 | Instrument panel - Thermal cycle |
| FCA PF 90223 par.6.2.1 | Material Requirements |
| FCA PF 90223 par.6.2.2 | Olfactory requirements |
| FCA PF 90223 par.6.2.3 | Fogging requirements |
| FCA PF 90223 par.6.3.12 | Part Identification and Marking |
| FCA PF 90223 par.6.3.13 | Traceability Requirements |
| FCA PF.90155 par.5.1 | Thermal shock |
| FCA PF.90155 par.5.2 | Thermal cycling |
| FCA PF.90155 par.5.3 | Cold impact |
| FCA PF.90155 par.5.4 | Humidity resistance |
| FCA PF.90155 par.5.5 | Extended heat ageing |
| FCA PF.90155 par.5.6 | Dimensional stability |
| FCA PF.90155 par.5.8 | Corrosion of mechanical fasteners |
| FCA PF.90155 par.5.9 | Chemical resistance |
| FDA 21 CFR sect. 177.1550 | Perfluorocarbon resins - Maximum extractable fraction |
| Ferrari ST LAB 040 | Crock mar resistance |
| FIAT 50180-A1 | Corrosion Tests |
| FIAT 50184 - Metodo B | Damp heat behavior |
| FIAT 50451 | Vehicle Exteriors - Accelerated aging by atmospheric agents |
| FIAT 50451/01 | Accelerated aging in sunlight |
| FIAT 50457 | Non-metallic materials - Specular gloss for paints, varnishes and enamels by glossmeter. |
| FIAT 50461 | Paints and varnishes - Adhesion resistance test of inorganic and organic trims by squaring off. |
| FIAT 50470 | Water immersion resistance test |
| FIAT 50471/01 | Alternating ultraviolet radiation-humidity resistance test |
| FIAT 50488 | Determination of the abrasion resistance of protective coatings by means of metallic grit |
| FIAT 50488/02 | Resistance to wear of aesthetic finishes |
| FIAT 50560 | Linear expansion coefficient check for thermoset plastics |
| FIAT 7.G2183 | Determination of internal impurities in components of fluid circulation systems |
| FIAT 7-G2000 | Resistance to combustion of non-metallic materials for the interior of the passenger compartment |
| FIAT 7-G2090 | Determination of formaldehyde release for single parts |
| FIAT 7-M0005 | Paints and varnishes - Scratch resistance |
| FIAT 9.02132/02 par.2.3.7 | Resistance to thermal cycles |
| FIAT 9.02132/02 par.2.3.9 | Heat age Exposure Test |
| FIAT 9.02215 par.5.2 | Dimensional Stability |
| FIAT 9.02215 par.5.3 | Resistance to cold impact |
| FIAT 9.02215 par.5.4 | Resistance to chemicals |
| FIAT 9.02215 par.5.5 | Burning velocity |
| FIAT 9.02215 par.9.3 | Thermal ageing |
| FIAT 9.02215 par.9.4 | Resistance to thermal cycles |
| FIAT 9.03109:2008 par.2.10 | Damp heat behavior |
| FIAT 9.03109:2008 par.2.11 | Resistance to thermal cycles |
| FIAT 9.03109:2008 par.2.12 | Low temperature behaviour |
| FIAT 9.03109:2008 par.2.9.1 | Dimensional Stability |
| FIAT 9.03109:2008 par.2.9.2 | Heat Stroke |
| FIAT 9.03147 par.2.19 | Adhesion - resistance to detachment by shear |
| FIAT 9.07301 par.2.10 | Damp heat behavior |
| FIAT 9.07301 par.2.11 | Behaviour in cold weather |
| FIAT 9.07301 par.2.12 | Resistance to cold impact |
| FIAT 9.07301 par.2.13 | Abrasion resistance |
| FIAT 9.07301 par.2.7 | Thermal ageing |
| FIAT 9.07301 par.2.8 | Hot stiffness |
| FIAT 9.07301 par.2.9 | Resistance to thermal cycles |
| FIAT 9.55253 par.2.10.2 | Dimensional Stability |
| FIAT 9.55253 par.2.10.3 | Heat stroke |
| FIAT 9.55253 par.2.10.4 | Thermal ageing |
| FIAT 9.55253 par.2.11 | Resistance to thermal cycles |
| FIAT 9.55253 par.2.12 | Damp heat aging |
| FIAT 9.55253 par.2.14 | Resistance to cold impact |
| FIAT 9.55253 par.2.16.2 | Accelerated ageing in sunlight |
| FIAT 9.55253 par.2.17 | Resistance to chemicals |
| FIAT 9.55253 par.2.18 | Burn rate test |
| FIAT 9.55253 par.2.6.5 | Assessment of passenger compartment olfactory quality |
| FIAT 9.55253 par.2.7.1 | Molding check - sectioning |
| FIAT 9.55253 par.2.7.2 | Molding check - Surfactant |
| FIAT 9.55253 par.2.7.3 | Thermal shock resistance |
| Fiat 9.55260/02 Par.2.5 Rigidezza a compressione | Sealing components and-or anti-vibration insert - Compressive stiffness |
| Fiat 9.55260/02 Par.2.7 Assorbimento d'acqua | Sealing components and-or anti-vibration insert - Water absorption |
| Fiat 9.55260/02 Par.2.8 Deformazione residua | Sealing components and-or anti-vibration insert - Residual deformation |
| FIAT 9.55710 par.2.4.4 | Resistance to detachment by shear after hardening |
| FIAT 9.55842/01 par.2.10 | Resistance to UV rays |
| FIAT 9.55842/01 par.2.11 | Vehicle interior components - Accelerated aging |
| FIAT 9.55842/01 par.2.12 | Resistance to damp |
| FIAT 9.55842/01 par.2.13 | Resistance to water |
| FIAT 9.55842/01 par.2.14 | Resistance to temperature variations |
| FIAT 9.55842/01 par.2.15 | Resistance to chemical aggressions |
| FIAT 9.55842/01 par.2.16 | Resistance to alcohol |
| FIAT 9.55842/01 par.2.17 | Resistance to fuel |
| FIAT 9.55842/01 par.2.19 | Wear resistance |
| FIAT 9.55842/01 par.2.20 | Resistance to stone-chipping |
| FIAT 9.55842/01 par.2.22 | Scratching test by brushing |
| FIAT 9.55842/01 par.2.4 | Visual inspection |
| FIAT 9.55842/01 par.2.5 | Thickness |
| FIAT 9.55842/01 par.2.6 | Hardness |
| FIAT 9.55842/01 par.2.7 | Adhesion |
| FIAT 9.55842/01 par.2.8 | Gloss |
| FIAT 9.55842/01 par.2.9 | Accelerated weathering with adhesion and gloss evaluation |
| FMVSS 302 | Flammability of interior materials |
| FORD FLTM BI 161-01 | Mar resistance determination for automotive coatings |
| FORD FLTM BO 162-01 | Resistance to scratch and mar |
| FPI.MAN050 par.4.2 | Impurities check |
| GIS CW6 Annex D | Annex D - Evaluation of Resistance to Water Immersion |
| GIS CW6 AnnexE | Annex E - Evaluation of Resistance to Heat Blistering |
| GMW14688 Method B | Mar resistance |
| GMW14688 Method A | Scratch Resistance |
| IEC 243-1 | Methods of test for electric strength of solid insulating materials - Part 1: Test at power frequencies |
| IEC 60068-2-11 | Environmental testing - Part 2-11: Tests - Test Ka: Salt mist |
| IEC 60068-2-2 | Enviromental testing - Dry heat |
| IEC 60068-2-5 | Simulation solar radiation at ground level - Solar radiation testing and weathering |
| IEC 60068-2-52 | Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) |
| IEC 60068-2-70 | Environmental testing - Abrasion of markings and letterings caused by rubbing of fingers and hands |
| IEC 60156 -max 60kV; | Breakadown voltage determinazion at power frequency |
| IEC 60167 | (Withdrawn and replaced by IEC 62631-3-3) Methods of test for the determination of the insulation resistance of solid insulating materials |
| IEC 60216-1 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| IEC 60243-1 - max 60kV; | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60247 - d.c. resistivity; | d.c. resistivity |
| IEC 60695-10-2 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| IEC 60695-10-2 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| IEC 61215 par.10.10 | Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval |
| IEC 61215 par.10.11 | Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Thermal cycling test |
| IEC 61215 par.10.12 | Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Humidity-freeze test |
| IEC 61215 par.10.13.2 | Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Damp heat test |
| IEC 61215-1 | Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1: Test requirements |
| IEC 61300-2-22 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Change of temperature |
| IEC 61300-2-34 | Fibre optic interconnecting devices and passive components - Resistance to solvents and contaminating fluids |
| IEC 61340-2-3 | Electrostatics - Surface and volume resistance |
| IEC 61386-1 Par.10.2 Compression Test | Conduit system for cable management - Mechanical properties: compression test |
| IEC 61386-1 Par.10.2 Compression Test | |
| IEC 61386-1 Par.10.3 Impact test | Conduit system for cable management - Mechanical properties: impact test |
| IEC 61386-1 Par.12.2 Thermal resistance | Conduit system for cable management - Thermal properties: thermal resistance |
| IEC 62108 par.10.6 | Concentrator photovoltaic (CPV) modules and assemblies - Design qualification and type approval - Thermal Cycling Test |
| IEC 62108 par.10.7 | Concentrator photovoltaic (CPV) modules and assemblies - Design qualification and type approval - Damp Heat Test |
| IEC 62108 par.10.8 | Concentrator photovoltaic (CPV) modules and assemblies - Design qualification and type approval - Humidity freeze test |
| IEC 62262 | Enclosures for Electrical Equipment - Degrees of Protection Provided Against External Mechanical Impacts (IK Code) |
| IEC 62631-2-1 | Dielectric and resistive properties of solid insulating materials - Part 2-1: Relative permittivity and dissipation factor - Technical Frequencies (0,1 Hz - 10 MHz) - AC Methods |
| IEC 62631-3-1 | Electrical insulation materials - Dielectric and resistive properties of solid insulating materials – Part 3-1: Determination of resistive properties (DC methods) – Volume resistance and volume resistivity |
| IEC 62631-3-2 | Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC methods) - Surface resistance and surface resistivity |
| IEC 62631-3-3 | Dielectric and resistive properties of solid insulating materials - Part 3-3: Determination of resistive properties (DC methods) - Insulation resistance |
| IMO MSC.215(82) - Annex 1 Appendix 1 | Paints and varnishes - Wave Tank Test |
| IMO MSC.215(82) - Annex 1 Appendix 1.7 | Paint and varnish - Cross-over test - Cathodic disbonding |
| IMO MSC.215(82) - Annex 1 Appendix 2 | Paints and varnishes - Condensation chamber test |
| Invecchiamento in azoto protossido (N2O) | Plastic materials - Autoclave with dinitrogen monoxide |
| IPC-TM-650 2.4.24.1 | Laminates - Time to Delamination - TMA Method |
| ISO 10304-1 | Amount of chlorides, fluorides, nitrates, nitrites and sulphates |
| ISO 10477 par. 7.5 | Flexural strength |
| ISO 10545-8 | Ceramic tiles - Part 8: Determination of linear thermal expansion |
| ISO 105-A02 | Textiles - Grey scale for assessing change in colour |
| ISO 11347 | Ships and marine technology -- Large yachts - Measurement and assessment of the visual appearance of coatings |
| ISO 11359-2 | Plastics - Thermomechanical analysis (TMA) |
| ISO 11359-3 | Plastics — Thermomechanical analysis (TMA) - Part 3: Determination of penetration temperature |
| ISO 11443 | Plastics - Determination of the fluidity of plastics using capillary and slit-die rheometers |
| ISO 11503 | Paints and varnishes — Determination of resistance to humidity (intermittent condensation) |
| ISO 1183-2 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method |
| ISO 12736 Annex I | Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures - Ring shear test |
| ISO 12736-1 par.7.2.2.2 | Oil and gas industries including lower carbon energy - Wet thermal insulation systems for pipelines and subsea equipment - Part 1: Validation of materials and insulation systems - Water absorption test |
| ISO 12736-1 par.7.2.2.3 | Oil and gas industries including lower carbon energy - Wet thermal insulation systems for pipelines and subsea equipment - Part 1: Validation of materials and insulation systems - Wet heat exposure |
| ISO 12736-1 par.7.2.2.4 | Wet thermal insulation systems for pipelines and subsea equipment - Part 1: Validation of materials and insulation systems - Dry heat exposure |
| ISO 12736-1 par.C.2.3 | Hydrostatic compression collapse test |
| ISO 12736-1 par.C.3 | Tri-axial compression and creep test |
| ISO 12944-6 | Paints and varnishes - Corrosion protection of steel structures by protective paint systems |
| ISO 12944-9 | Paints and varnishes - Protective paint systems and laboratory performance test method for offshore and related structures |
| ISO 12944-9 Annex C | Paint and varnish - Fingerprint - Main parameters |
| ISO 13320 | Particle size analysis - Laser diffraction methods |
| ISO 13468-1 | Plastics - Determination of the total luminous transmittance of transparent materials — Part 1: Single-beam instrument |
| ISO 13953 | Polyethylene (PE) pipes and fittings - Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 13954 | Plastics pipes and fittings - Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| ISO 1419 Method C | Rubber- or plastics-coated fabrics - Accelerated-ageing tests: tropical test |
| ISO 14309 | Rubber, vulcanized or thermoplastic - Determination of volume and-or surface resistivity |
| ISO 1431-1 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Part 1: Static and dynamic strain testing |
| ISO 14420 | Carbonaceous products for the production of aluminium — Baked anodes and shaped carbon products - Determination of the coefficient of linear thermal expansion |
| ISO 14782 | Plastics - Determination of haze for transparent materials |
| ISO 15105-2 | Plastics — Film and sheeting - Determination of gas-transmission rate — Part 2: Equal-pressure method |
| ISO 15113 proc. A | Rubber - Determination of frictional properties - Procedure A - Initial friction measurements |
| ISO 15113 proc.B | Rubber - Determination of frictional properties - Porcedure B - service behaviour |
| ISO 15113 proc.C | Rubber - Determination of frictional properties - Procedure C (tests with added lubricants or contaminants) |
| ISO 1518-1 | Paints and varnishes - Scratch resistance |
| ISO 15711 | Paints and varnishes - Determination of resistance to cathodic disbonding of coatings exposed to sea water |
| ISO 15741 Annex A | Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases - Ash |
| ISO 15741 Annex C par.C.4.2 | Paints and varnishes - Cyclic pressure test |
| ISO 15741 Annex C par.C.4.3 | Paints and varnishes - Decompression blistering test |
| ISO 15741 Annex D | Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases - Hydraulic pressure blistering |
| ISO 15741 Annex G | Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases - Wet-sponge test |
| ISO 15741 par. 4.3.6 | Friction-reduction coatings for the interior pipelines - Resistance to salt spray |
| ISO 15741 par. 4.3.7 | Friction-reduction coatings for the interior pipelines - Resistance to artificial ageing |
| ISO 15741 par.6.2.5 | Paints and varnishes - Friction-reduction coatings for the interior of on- and offshore steel pipelines for non-corrosive gases - Curing test |
| ISO 16145-1 | Ships and marine technology - Protective coatings and inspection method Dedicated sea water ballast tanks |
| ISO 16232 | Road vehicles - Cleanliness of components and systems |
| ISO 16750-3 par.4.3 | Free fall |
| ISO 16750-4 par. 5.4.2 | Road vehicles - Environmental conditions and testing for electrical and electronic equipment Climatic loads - Splash water test |
| ISO 16750-5 | Environmental conditions and testing for electrical and electronic equipment - Chemical loads |
| ISO 16770 | Materie plastiche -- Determinazione della fessurazione da stress ambientale (ESC) del polietilene - Prova di scorrimento a intaglio completo (FNCT) |
| ISO 16961 | Oil and gas industries including lower carbon energy - Internal coating and lining of steel storage tanks |
| ISO 17054 | Steel - Spectrometry XRF on high alloy steel |
| ISO 17744 | Plastics - Determination of specific volume as a function of temperature and pressure (pvT diagram) — Piston apparatus method |
| ISO 17834 | Thermal spraying — Coatings for protection against corrosion and oxidation at elevated temperatures |
| ISO 18468 | Ductile iron fittings, accessories and their joints and valves - Epoxy coating |
| ISO 18488 | Polyethylene (PE) materials for piping systems - Determination of Strain Hardening Modulus in relation to slow crack growth - Test method |
| ISO 18553 | Polyolefin - Method for the assessment of the degree of pigment or carbon black dispersion |
| ISO 18555 | Metallic and other inorganic coatings - Determination of thermal conductivity of thermal barrier coatings |
| ISO 18796-1 | Petroleum, petrochemicals and natural gas industries - Internal coating and lining of carbon steel process vessels — Part 1: Technical requirements |
| ISO 18797-1 | Petroleum, petrochemical and natural gas industries -- External corrosion protection of risers by coatings and linings - Elastomeric coating systems-polychloroprene or EPDM |
| ISO 19277 par. 7.2 | Qualification testing and acceptance criteria for protective coating systems under insulation - Assessment of adhesion and artificial ageing |
| ISO 19277 par. 7.3 | Qualification testing and acceptance criteria for protective coating systems under insulation - Thermal cycling test |
| ISO 19277 par. 7.4 | Qualification testing and acceptance criteria for protective coating systems under insulation - Multi-phase CUI cyclic corrosion test |
| ISO 19277 par. 8.1 | Qualification testing and acceptance criteria for protective coating system under insulation - Cryogenic cycling testing |
| ISO 19277 par. 8.2 | Qualification testing and acceptance criteria for protective coating system under insulation - Vertical pipe test |
| ISO 20653 | Road vehicles- Degrees of protection (IP code) - Protection of electrical equipment against foreign objects, water and access |
| ISO 20795-1 par. 8.5.3.5 | Ultimate flexural strength and flexural modulus |
| ISO 20795-2 par. 8.3.2.5 | Ultimate flexural strength and flexural modulus |
| ISO 2137 | Petroleum products and lubricants - Determination of cone penetration of lubricating greases and petrolatum |
| ISO 2176 | Lubricating grease - Dropping point |
| ISO 2177 | Metallic coatings - Measurement of coating thickness — Coulometric method by anodic dissolution |
| ISO 21809-11 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Coatings for in-field application, coating repairs and rehabilitation |
| ISO 21809-4 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems Polyethylene coatings (2-layer PE) |
| ISO 2207 | Petroleum waxes - Determination of congealing point |
| ISO 22309 | Microbeam analysis - Quantitative analysis using energy-dispersive spectrometry (EDS) for elements with an atomic number of 11 (Na) or above |
| ISO 22479 | Corrosion of metals and alloys - Sulfur dioxide test in a humid atmosphere (fixed gas method) |
| ISO 22680 | Metallic and other inorganic coatings - Measurement of the linear thermal expansion coefficient of thermal barrier coatings |
| ISO 22883 Par.5.5 | Castors and wheels: Requirements for applications up to 1,1 m-s (4 km-h) - Electrical resistence test |
| ISO 22969 | Paints and varnishes - Determination of solar reflectance |
| ISO 22970 | Paints and varnishes - Test method for evaluation of adhesion of elastic adhesives on coatings by peel test, peel strength test and tensile lap-shear strength test with additional stress by condensation test or cataplasm storage |
| ISO 24338 | Laminate floor coverings - Determination of abrasion resistance |
| ISO 2602 | Statistical interpretation of test results |
| ISO 2810 | Paints and varnishes - Natural weathering of coatings - Exposure and assessment |
| ISO 2815 | Paints and varnishes - Buchholz indentation test |
| ISO 3146, Method A | Plastics - Melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube |
| ISO 34-1 | Rubber, vulcanized or thermoplastic - Determination of tear strength — Part 1: Trouser, angle and crescent test pieces |
| ISO 3451-1 + EPA 6010D + EPA 3051A | Ash characterization - screening of the 8 metals mainly present |
| ISO 37 | Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties |
| ISO 4287 | Geometrical Product Specifications (GPS) - Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 4433-2 | Thermoplastics - Resistance to liquid chemicals: polyolefin |
| ISO 4532 | Vitreous and porcelain enamels - Determination of the resistance of enamelled articles to impact |
| ISO 458-2 | Plastics - Determination of stiffness in torsion of flexible materials -- Part 2 Application to plasticized compounds of homopolymers and copolymers of vinyl chloride |
| ISO 4593 | Plastics - Film and sheeting -- Determination of thickness by mechanical scanning |
| ISO 4623-2 | Paints and varnishes - Determination of resistance to filiform corrosion Aluminium substrates |
| ISO 4649 | Rubber, vulcanized or thermoplastic - Determination of abrasion resistance using a rotating cylindrical drum device |
| ISO 48-4 | Rubber, vulcanized or thermoplastic - Determination of hardness - Part 4: Indentation hardness by durometer method (Shore hardness) |
| ISO 4897 | Cellular plastics - Determination of the coefficient of linear thermal expansion of rigid materials at sub-ambient temperatures |
| ISO 5470-1 | Rubber- or plastics-coated fabrics - Determination of abrasion resistance Taber abrader |
| ISO 565 | Granule Size |
| ISO 6270-3 | Paints and varnishes - Determination of resistance to humidity Condensation (in-cabinet exposure with heated, bubbling water reservoir) |
| ISO 6452 | Rubber- or plastics-coated fabrics - Determination of fogging characteristics of trim materials in the interior of automobiles |
| ISO 6603-2 | Plastics - Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
| ISO 6721-1 | Plastics - Determination of dynamic mechanical properties — Part 1: General principles |
| ISO 6721-4 | Plastics - Determination of dynamic mechanical properties Tensile vibration -- Non-resonance method |
| ISO 6721-5 | Plastics — Determination of dynamic mechanical properties - Part 5: Flexural vibration — Non-resonance method |
| ISO 6964 Met.C | Polyolefin pipes and fittings - Carbon black content |
| ISO 75-1 | Plastics - Determination of temperature of deflection under load — Part 1: General test method |
| ISO 75-2 | Plastics - Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 75-3 | Plastics - Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics |
| ISO 7765-1 | Plastics film and sheeting - Determination of impact resistance by the free-falling dart method Staircase methods |
| ISO 7765-2 | Plastics film and sheeting - Determination of impact resistance by the free-falling dart method Instrumented puncture test |
| ISO 7991 | Glass — Determination of coefficient of mean linear thermal expansion |
| ISO 812 | Rubber, vulcanized or thermoplastic - Determination of low-temperature brittleness |
| ISO 816 | Rubber, vulcanized - Determination of tear strength of small test pieces (Delft test pieces) |
| ISO 8179-1 | Ductile iron pipes, fittings, accessories and their joints — External zinc-based coating - Part 1: Metallic zinc with finishing layer |
| ISO 8179-2 | Ductile iron pipes, fittings, accessories and their joints — External zinc-based coating - Part 2: Zinc-rich paint |
| ISO 8296 | Wetting tension |
| ISO 8301 | Thermal insulation - Determination of steady-state thermal resistance and related properties - Heat flow meter apparatus |
| ISO 8302 | Thermal insulation - Determination of steady-state thermal resistance and related properties -- Guarded hot plate apparatus |
| ISO 8308 | Rubber and plastics hoses and tubing — Determination of transmission of liquids through hose and tubing walls |
| ISO 8690 | Measurement of radioactivity — Gamma ray and beta emitting radionuclides — Test method to assess the ease of decontamination of surface materials |
| ISO 899-1 | Plastics - Determination of creep behaviour Tensile creep |
| ISO 899-2 | Plastics - Determination of creep behaviour Flexural creep by three-point loading |
| ISO 9142 | Adhesives - Guide to the selection of standard laboratory ageing conditions for testing bonded joints |
| ISO 9237 | Textiles - Determination of the permeability of fabrics to air |
| ISO 9352 | Plastics - Determination of resistance to wear by abrasive wheels |
| ISO 974 | Plastics - Determination of the brittleness temperature by impact |
| ISO 9852 | Unplasticized poly(vinyl chloride) (PVC-U) pipes - Dichloromethane resistance at specified temperature (DCMT) -- Test method |
| ISO 9854-1 | Thermoplastics pipes for the transport of fluids - Pendulum impact strength by the Charpy method |
| ISO/TR 19402 | Paints and varnishes - Adhesion of coatings |
| ISO/TR 21555 | Paints and varnishes - Overview of test methods on hardness and wear resistance of coatings |
| ISO/TS 19392-1 | Paints and varnishes - Coating systems for wind-turbine rotor blades Minimum requirements and weathering |
| ISO/TS 19397 | Coatings - Determination of the film thickness of coatings using an ultrasonic gage |
| ISO12736 par.A.2.2 | Petroleum and natural gas industries — Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures - Hydrostatic compression creep test |
| IVECO 15-0432 | Resistance to stress-cracking of plastics |
| IVECO 15-0461 | Cross-cut adhesion test |
| IVECO 15-0470 | Determination of water resistance of paints, enamels, etc. |
| IVECO 15-0473 | Determination of solvent resistance of paints, enamels, etc. |
| IVECO 15-0493 | Deformations of organic coatings applied on flexible plastic material |
| IVECO 15-5232 - Residuo alla calcinazione | Ash content |
| IVECO 15-6021 | Persoz hardness |
| IVECO 15-6023 | Resistance to stone chipping of paints, enamels, etc. |
| IVECO 15-6035 | Determination of resistance to bubble corrosion (scab-corrosion) |
| IVECO 16-0135 Metodo A1 | Salt spray test |
| IVECO 16-0140 | Damp heat behavior |
| IVECO 16-0141 | Enviromental test condition for hot and dry aging |
| IVECO 16-0146 | Rapid temperature change for components and assemblies |
| IVECO 16-0154 | Burning rate |
| IVECO 16-0160 par.5.2 - Scratch | Scratch test |
| IVECO 16-0160 par.5.3 - Mar | Mar resistance |
| IVECO 16-0170 | Behaviour to light |
| IVECO 16-0176 | Burning rate of non-metallic materials |
| IVECO 16-0180 Met.B | Plastics - Resistance to atmospheric agents |
| IVECO 16-0180 Met.C | Resistance to atmospheric agents |
| IVECO 16-0235 | Wear resistance of aesthetic finishes |
| IVECO 18-1601 - CSS | Reaction to superficial sweat |
| IVECO 18-1601 - Durezza Persoz | Persoz hardness |
| IVECO 18-1601 - Res. Alcohol | Denatured ethyl alcohol resistance |
| IVECO 18-1601 - Thickness | Thickness |
| IVECO 18-1724 Par. 3.2.1 | Primer for glass application of polyurethane adhesive - Composition by way of example |
| IVECO 18-1724 Par. 3.2.2 | Primer for glass application of polyurethane adhesive - Volume mass |
| IVECO 18-1724 Par. 3.2.3 | Primer for glass application of polyurethane adhesive - Dry residue 2 h at 105 ±2 °C |
| IVECO 18-1724 Par. 3.2.4 | Primer for glass application of polyurethane adhesive - Viscosity (Ford Cup 4) |
| IVECO 18-1724 Par. 3.3.1 | Primer for glass application of polyurethane adhesive - dry to touch |
| IVECO 18-8000 par. 10 | Thermal cycles resistance |
| IVECO 18-8000 par. 11 | Behaviour to humid high temperatures |
| IVECO 18-8000 par. 12 | Resistance to surface damage |
| IVECO 18-8000 par. 13 | Indentation |
| IVECO 18-8000 par. 14 | Coldblast resistance |
| IVECO 18-8000 par. 15.1 | Accelerated aging to atmospheric agents |
| IVECO 18-8000 par. 15.2 | Ageing to light |
| IVECO 18-8000 par. 16 | Resistance to chemicals |
| IVECO 18-8000 par. 17 | Resistance to tensile cracking |
| IVECO 18-8000 par. 18 | Abrasion resistance |
| IVECO 18-8000 par. 20 | Hydrolysis resistance |
| IVECO 18-8000 par. 23 | Combustion speed |
| IVECO 18-8000 par. 24 | Seal of threaded seat and metal inserts |
| IVECO 18-8000 par. 8.2 | Surfactant |
| IVECO 18-8000 par. 9.1 | Painting cycle simulation |
| IVECO 18-8000 par. 9.2 | Dimensional Stability |
| IVECO 18-8000 par. 9.3 | Heat Stroke |
| IVECO 18-8000 par. 9.4 | Thermal ageing |
| IVECO 18-8000 par.8.1 | Dissection |
| IVECO 18-8061 par.5.11 | Dimensional stability |
| IVECO 18-8061 par.5.12 | Thermal shock behaviour |
| IVECO 18-8061 par.5.13 | Damp heat behaviour |
| IVECO 18-8061 par.5.15 | Low temperature behaviour |
| IVECO 18-8061 par.5.16 | Thermal cycles |
| IVECO 18-8061 par.5.17.4 | Resistance to chemicals |
| IVECO 18-8069 par.4.16 | Adhesion test - shear strength of bond |
| IVECO 18-8303 | Sound-proof panels, flat and moulded |
| IVECO 18-8311 | Rivestimenti preformati per interno padiglioni veicoli |
| JDQ 201B4 | Electrical and electronic components - Chemical resistance |
| KLT FCA AGS 560 | KLT FCA AGS |
| LMBG § 35 L 00.00-6 1 | Migrazione globale Media nel simulante (mg-kg) Ammine Aromatiche Primarie: Migrazione specifica (mg-kg) |
| LP.7P065 | Seat complete enviromental exposure thermal cycle |
| M.I. 192 R00 2023 + APAT CNR IRSA 4020 Man 29 2003 + IRSA 4150 A Man 29 2003 | Cloruri (mg-kg s.s.), Solfati (SO4) (mg-kg s.s.), Solfiti (come SO3) (mg-kg s.s.) |
| MAN 277 | Coatings - Adhesion test (Scratch test) |
| MBN 10494-5 par.5.1.1 | Manual scratch test |
| Metodo interno lab.ID93 - ICP | Metals - Phosphorus content by humid chemical analysis |
| MicroRAMAN | Micro Raman Analysis |
| MIL-STD-810G method 504.1 Procedure I par.2.2.6 | Contamination by fluids @23°C |
| MIL-STD-810G method 504.1 Procedure I par.2.2.6 | Contamination by fluid @ high temperature |
| MIL-STD-810G method 505.6 Procedure II | SOLAR RADIATION (SUNSHINE) |
| MIL-STD-810G method 508.6 method A | Fungus |
| MIL-STD-810G method 509.6 procedure 4.5.2 | Salt fog |
| MSL 10.23.0007 par.4.1.1 | Cross hatch adhesion test |
| MSL 10.23.0007 par.5.1.1 | Gloss level |
| MSL 10.23.0007 par.5.1.2.2 | Spectrometer colour match |
| MSL 10.23.0007 par.5.1.3 | Surface Finish |
| MSL.10.23.0007 par.4.5 | Heat Ageing test |
| NACE No.12 par. 6.5 | Specification for the Application of Thermal Spray Coatings (Metallizing) of Aluminum, Zinc, and Their Alloys and Composites for the Corrosion Protection of Steel - Bend test |
| NACE SP0188 | Paints and varnishes - Discontinuity (Holiday) Testing of New Protective Coatings on Conductive Substrates |
| NACE SP0394 Appendix A | Application, Performance, and Quality Control of Plant-Applied Single Layer Fusion-Bonded Epoxy External Pipe Coating - Density - Specific gravity |
| NACE SP0394 Appendix C | Application, Performance, and Quality Control of Plant-Applied Single Layer Fusion-Bonded Epoxy External Pipe Coating - Gel time |
| NACE SP0394 Appendix D | Glass transition and heat of reaction |
| NACE SP0394 Appendix E | Plant-applied Single-Layer Fusion-Bonded Epoxy External Pipe Coating - Moisture analysis determination |
| NACE SP0394 Appendix F | Fusion Bonded Epoxy External Pipe Coating - Cathodic disbondment |
| NACE SP0394 Appendix G | Porosity of the coating |
| NACE SP0394 Appendix H | Flexibility test |
| NACE SP0394 Appendix I | Impact test |
| NACE SP0394 Appendix J | Hot water soak |
| NACE SP0394 Appendix K | Test for interface contamination of the coating |
| NACE SP0394 Appendix L | Application, Performance, and Quality Control of Plant-Applied Single Layer Fusion-Bonded Epoxy External Pipe Coating - Particle size - Sieve |
| NACE SP0394 Appendix M | Plant-applied Single-Layer Fusion-Bonded Epoxy External Pipe Coating - Total volatile-moisture of epoxy powder mass loss |
| NACE SP0395 | (formerly RP0395), Fusion-Bonded Epoxy Coating of Steel Reinforcing Bars - |
| NACE TM0104 sect. 12 | Offshore Platform Ballast Water Tank Coating System Evaluation - Thick-Film Cracking Test |
| NACE TM0115 | Coated steel structures under cathodic protection - Cathodic disbondment |
| NACE TM0174 | Laboratory Methods for the Evaluation of Protective Coatings and Lining Materials on Metallic Substrates in Immersion Service |
| NACE TM0185 | Evaluation of internal plastic coatings for corrosion control of tubular goods - Autoclave testing |
| NACE TM0208 | Vapor- Inhibiting Ability of Volatile Corrosion Inhibitor Materials for Temporary Protection of Ferrous Metal Surfaces |
| NACE TM0404 sect. 12 | Offshore Platform Coating System Evaluation - Flexibility Test |
| NACE TM0404 sect. 9 | Offshore Platform Coatings System Evaluation - Thermal-Cycling Resistance Test |
| NATIONALGRID T.SC.PW.6.1 J229 Appendix J | FBE coating - Evaluation of resistance to heat blistering |
| NATIONALGRID T.SC.PW.6.1 J229:2018 Appendix F | FBE coating - Impact resistance |
| NES M0141 par.6.2.3 | Chipping resistance characteristics |
| NES M0141 par.6.2.8 | Abrasion resistance characteristics |
| NES M0141 par.6.4.1 B | Weathering resistance characteristics - Accelerated exposure |
| NF A 49-711 Appendix K | External three layer polypropylene coating applicated by extrusion - Cathodic disbonding test under negative polarization |
| NF F 31-112 | Railway rolling stock - Protection in relation to graffiti - Tests procedures and methodes of valuation, behaviour of materials and products of expulsion - Matériel roulant ferroviaire - Protection vis-à-vis des graffiti - Procédures d essais et méthodes d évaluation du comportement des matériaux et des produits d élimination |
| NF M07-023 + M.I. 173 R00 2022 | Wax - Content of aggressive elements in the wax by Ion Chromatography and ICP - Method for the extraction of anions with solvent and then in water |
| NF T30-012 | Paints and varnishes - Determination of ash content in varnishes, paints and similar products |
| NF T60-119 | Petrolatum products - Cone Penetration |
| NF T60-121 | Petroleum products - Determination of the conventional melting point of petroleum waxes and petroleum jellies |
| NF T60-128 | Petroleum waxes and paraffins - Determination of congealing point |
| NF T60-191 | Petroleum products and lubricating greases - Oil separation on storage - method under pressure, static conditions |
| NORSOK standard M-501 | Paint and varnishes - Surface preparation and protective coating |
| NWSP 70.1 | Textiles - Determination of permeability of fabrics to air |
| PdP-SD1701 rev0 + ISO1183-1 + ASTM D2842 | Apparent saturated density in water after 96hours of water immersion at 12 bar |
| PdP-SD2010 rev0 | PU foam - Apparent saturated density in water |
| PF.90131 Par 5.2 Tab.6 item1 | Mechanical Stresses - Dent resistance |
| PF.90131 Par 5.2 Tab.6 item2 | Mechanical Stresses - Cold impact resistance test |
| PF.90131 par.5.1.1 | Heat age Exposure Test |
| PF.90131 par.5.1.2 | Thermal cycle exposure test |
| PF.90131 par.5.1.3 | Humidity Aging Exposure Test |
| PF.90131 par.5.1.4 | Artificial Light Exposure Test |
| PF.90131 par.5.2.1 | Mold-in-Color Plastic Scratch and Mar Resistance |
| PF.90131 Par.5.2.3 | Whitening test procedure - LP.7M009 |
| PF.90131 Par.5.3.1 | Resistance to common household Fluids and cleaners Requirements |
| PF.90131 par.5.3.2 | Corrosion resistance test |
| PF.90131 Par.6.1 | Appearance requirements |
| Piaggio 2884 | Adhesion test |
| Piaggio 2888 | Salt spray resistance |
| Piaggio 2916 | Resistance to water immersion |
| Piaggio TS00068 | Accelerated light aging test by xenon test |
| Prova a fatica assiale customizzata a controllo di carico | Prova a fatica assiale customizzata a controllo di carico |
| PSA B14 2900 | Tightness against immersion by insulation resistance |
| PSA D45 1727 - Fogging | Interior trim materials and passenger compartment parts fogging |
| PV 3925 | Polymer Materials - Determination of Formaldehyde Emission - Measurement by a Modified Bottle Method |
| QUALICOAT - MACHU TEST par.2.11 | Liquid and powder organic coatings on aluminium - Mach test |
| RCSC Appendix A, sect. A.2.2 | Specification for Structural Joints Using High-Strength Bolts - DFT measurements |
| RCSC Appendix A, sect. A.3 | Specification for Structural Joints Using High-Strength Bolts - Slip coefficient determination |
| RCSC Appendix A, sect. A.4 | Specification for Structural Joints Using High-Strength Bolts - Tension creep determination |
| Regolamento UNECE n. 118 R118 Allegato 6 | Horizontal burning rate |
| Regolamento UNECE n. 118 R118 Allegato 7 | Melting behaviour of materials |
| Regolamento UNECE n. 118 R118 Allegato 8 | Vertical burning rate |
| Renault D421235 | Plastic or rubber parts - Impact behaviour |
| RFI DTC SI PS SP IFS 001 A | General technical specifications for civil works. |
| RMRS - Part XIII - MATERIALS - Par.2.5 TESTING OF ICE-RESISTANT COATINGS | Russian Maritime Register of Shipping - Part XIII - MATERIALS - TESTING OF ICE-RESISTANT COATINGS |
| RNES-G-00005 | Paint and varnishes - Corrosion test by automatic change of phases of salt spray drying and umidity (ECC1) |
| RNES-G-00007 | Cyclic Corrosion Test-IV - CCT-IV |
| SAE J 1645 | Fuel Systems and Components - Electrostatic Charge Mitigation |
| SAE J 2527 | Surface vehicle - Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Xenon-Arc Apparatus |
| SAE J1756 | Determination of the Fogging Characteristics of Interior Automotive Materials |
| SAE J2334 | Laboratory Cyclic Corrosion Test |
| SAE J2412 | Accelerated weathering |
| SAE J400 | Chip Resistance of Surface Coatings |
| SAE USCAR1-2 | Salt spray testing and evaluation of fasteners finishes |
| SPECIFICHE TECNICHE N. F 12 DEL 01.06.2018 - Resistenza allo strappo | Resistenza allo strappo con sistemi di sicurezza inseriti |
| SPECIFICHE TECNICHE N. F 12 DEL 01.06.2018 - Resistenza collegamento Passante cintura-Fondina. | Resistenza collegamento Passante cintura-Fondina. |
| SSPC-PA 2 | Paint application specification no. 2 - Measurement of dry coating thickness |
| SSPC-Paint 20 | Zinc-Rich Coating (Type I – Inorganic, and Type II – Organic) |
| TL 191 | Paint Finish of Exhaust System Parts: Surface Protection Requirements |
| TL 52316 par.4.3 | Ageing in coolant |
| TOYOTA ES - TSH3131G Par 4.6 | Impact resistance section 2.1 TSH 1504G:2022 |
| TOYOTA ES - TSM0502G_REV14 Par.4.5.2 | Impact Resistance test |
| TP-206 | ALEYSKA SHEAR STRESS TEST |
| TPJLR 52.004 | Resistance to Scratch |
| UL 746B | Standard for Polymeric Materials - Long Term Property Evaluations (Thermal Index) |
| UL 746C | Standard for Polymeric Materials - Use in Electrical Equipment Evaluations - Outdoor Suitability |
| UL 94 Orizzontale | Plastic materials in devices and appliances - Test for flammability |
| UL 94 Verticale | Tests for Flammability of Plastic Materials for Parts in Devices and Appliances - Vertical Burning Test V-0, V-1, or V-2 |
| UNI 10209 | Veicoli stradali. Verniciatura di particolari metallici vari. Prova di resistenza alla benzina. |
| UNI 10210 | Prova di resistenza ai lubrificanti |
| UNI 10559 | Paints and varnishes - Determination of abrasion resistance by "TABER" apparatus. |
| UNI 10667-2 Appendice A | Recycled polyethylene - Method for the determination of contamination |
| UNI 10667-2 Appendix A | Polyethylene produced from recycled material - Method for the determination of contamination |
| UNI 11271 | Determinazione del potere coprente di pitture in emulsione di colore bianco o chiaro |
| UNI 4291 | Determinazione della rigidita dielettrica a frequenza industriale |
| UNI 6065 | Elastomers - Tests on vulcanized and thermoplastic rubber - Tensile test |
| UNI 7796 par.6 | Anodic oxidation coatings on aluminium and aluminium alloys - Hard anodic films of great thickness |
| UNI 8298-1 | Resinous systems for horizontal and vertical surfaces - Part 1: Determination of the adhesion of the resinous system to the substrate |
| UNI 8298-9 | Abrasion resistance |
| UNI 8901 | Prodotti vernicianti - Determinazione della resistenza all urto. |
| UNI 9099 par. B.1 | Steel pipes for buried or submerged pipelines - External polyethylene coating applied by extrusion. |
| UNI 9099 par. B.3 | Impact resistance |
| UNI 9099 par. B.4 | Peel strength |
| UNI 9099 par. B.5 | Indentation resistance |
| UNI 9099 par. B.6 | Coating resistivity |
| UNI 9099 par. B.7 | Tensile test |
| UNI 9099 par. B.8.1 | Ultraviolet (UV) stability |
| UNI 9099 par. B.8.2 | Thermal stability |
| UNI 9099 par. B.9 | External polyethylene coating applied by extrusion - Cathodic disbondment |
| UNI 9395 | Paint scoring - pen method |
| UNI CEI EN ISO 80079-36 Annex D | Explosive atmospheres - Part 36: Non-electrical equipment for explosive atmospheres - Basic method and requirements - Charging tests with non-conductive materials |
| UNI EN 1015-12 | Mortar for masonry - Determination of adhesive strength to substrate |
| UNI EN 10169 | Continuously organic coated (coil coated) steel flat products - Technical delivery conditions |
| UNI EN 10289 Annex A | Steel Tubes And Fittings For Onshore And Offshore Pipelines - External liquid applied epoxy and epoxy-modified coatings |
| UNI EN 10289 Annex B | External liquid applied epoxy and epoxy-modified coatings - Holiday detection test |
| UNI EN 10289 Annex C | Steel tubes and fittings for onshore and offshore pipelines - Impact test |
| UNI EN 10289 Annex D | External liquid applied epoxy and epoxy-modified coatings - Adhesion test - Resistance to removal |
| UNI EN 10289 Annex E | External liquid applied epoxy and epoxy-modified coatings - Cathodic disbondment test |
| UNI EN 10289 Annex F | Steel tubes and fittings for onshore and offshore pipelines - Specific electrical insulation resistance test |
| UNI EN 10289 Annex G | External liquid applied epoxy and epoxy-modified coatings - Adhesion test after immersion in tap water |
| UNI EN 10289 Annex H | External liquid applied epoxy and epoxy-modified coatings - Indentation test |
| UNI EN 10289 Annex J | External liquid applied epoxy and epoxy-modified coatings - Thermal ageing |
| UNI EN 10289 par.7.4 | Steel tubes and fittings for onshore and offshore pipelines - External liquid applied epoxy and epoxy-modified coatings - Appearance |
| UNI EN 10301 Annex C | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas - Resistance to gas pressure variations |
| UNI EN 10301 Annex D | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas - Resistance to hydraulic blistering |
| UNI EN 10301 par.4.2.12 | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas - Ageing test |
| UNI EN 10301 par.7.4 | Steel tubes and fittings for on and offshore pipelines - Internal coating for the reduction of friction for conveyance of non corrosive gas - Cure test |
| UNI EN 10339 | Steel tubes for onshore and offshore water pipelines - Internal liquid applied epoxy linings for corrosion protection |
| UNI EN 10346 Annex A | Continuously hot-dip coated steel flat products for cold forming - Coating mass |
| UNI EN 1062-3 | Coating materials and coating systems for exterior masonry and concrete. - Determination of liquid water permeability |
| UNI EN 1062-6 | Coating materials and coating systems for exterior masonry and concrete - Determination of carbon dioxide permeability |
| UNI EN 1062-7 | Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Determination of crack bridging properties |
| UNI EN 1081 | Resilient, laminate and modular multilayer floor coverings - Determination of the electrical resistance |
| UNI EN 1107-1 | Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of dimensional stability |
| UNI EN 1149-1 | Protective clothing - Electrostatic properties - Part 1: Test method for measurement of surface resistivity |
| UNI EN 12068 Annex B | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Peeling resistance tape on external tape |
| UNI EN 12068 Annex C | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Peeling resistance tape on pipe surface or factory coating |
| UNI EN 12068 Annex D | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Lap shear resistance |
| UNI EN 12068 Annex E | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Thermal ageing resistance |
| UNI EN 12068 Annex G | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Indentation |
| UNI EN 12068 Annex H | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Impact resistance |
| UNI EN 12068 Annex J | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Specific insulation resistance |
| UNI EN 12068 Annex K | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Cathodic disbonding |
| UNI EN 12068 Annex P | Tapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Unrolling behavior |
| UNI EN 12201-2 par.7.2 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes - Mean outside diameter, out-of-roundness (ovality) and tolerances |
| UNI EN 12201-2 par.7.3 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes - Wall thicknesses and their tolerances |
| UNI EN 12224 | Geotextiles and geotextile-related products - Determination of the resistance to weathering |
| UNI EN 12280-3 | Rubber- or plastic-coated fabrics - Accelerated ageing tests - Part 3: Environmental ageing |
| UNI EN 12310-2 | Part 2: Plastic and rubber membrane for waterproofing roofs |
| UNI EN 12311-2 | Plastic and rubber sheets for roof waterproofing - Determination of tensile properties |
| UNI EN 12390-1 | Concrete - Testing hardened concrete |
| UNI EN 12390-7 | Concrete - Testing hardened concrete |
| UNI EN 12430 | Thermal insulating products for building applications - Determination of behaviour under point load |
| UNI EN 12457-2 | Leaching - Compliance test for leaching of granular waste materials and sludges - One stage batch test at a liquid to solid ratio of 10 l-kg for materials with particle size below 4 mm (without or with size reduction) |
| UNI EN 12614 | Products and systems for the protection and repair of concrete structures - Determination of glass transition temperatures of polymers |
| UNI EN 12664 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Dry and moist products of medium and low thermal resistance |
| UNI EN 12667 | Building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods |
| UNI EN 12691 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to impact |
| UNI EN 12814-2 | Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test |
| UNI EN 12899-1 par.4.1.1.5.1 | Fixed, vertical road traffic signs - Part 1: Fixed signs - Durability |
| UNI EN 12939 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Thick products of high and medium thermal resistance |
| UNI EN 13261 Annex G | Railway applications. Axles. - Impact resistance of protective coating |
| UNI EN 13261 Annex H | Railway applications. Axles - Chipping resistance of protective coating |
| UNI EN 13261 Annex I | Railway applications. Axles. - Resistance of the coating to specific corrosive products |
| UNI EN 13261 Annex J | Railway applications. Axles. - Resistance of the protective coating under cyclic mechanical stess |
| UNI EN 13295 | Products and systems for the protection and repair of concrete structures - Determination of resistance to carbonation |
| UNI EN 1337-3 | Structural bearings - Part 3: Elastomeric bearings |
| UNI EN 1337-9 | Structural bearings - Protection |
| UNI EN 13438 | Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes |
| UNI EN 13495 | Thermal insulation products for building applications - Determination of the pull-off resistance of external thermal insulation composite systems |
| UNI EN 13523-10 | Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation |
| UNI EN 13523-2 | Coil coated metals - Test methods - Part 2: Specular gloss |
| UNI EN 13523-27 | Coil coated metals - Test methods. Resistance to humid poultice (Cataplasm test) |
| UNI EN 13523-3 | Coil coated metals - Test methods - Part 3: Colour difference - Instrumental comparison |
| UNI EN 1359 par. 6.4 | Diaphragm gas meters - Corrosion protection |
| UNI EN 13657 + EPA 6010C | Characterization of waste - Digestion for subsequent determination of aqua regia soluble portion of elements |
| UNI EN 1393 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial longitudinal tensile properties |
| UNI EN 14074 par. 6.2.2. | Office furniture - Tables and desks and storage furniture - Durability test of extension elements |
| UNI EN 14074 par. 6.2.3. | Office furniture - Tables and desks and storage furniture - Slam open of extension elements |
| UNI EN 14074 par. 6.3.3. | Office furniture - Tables and desks and storage furniture - Durability test on hinged or pivoted doors |
| UNI EN 14147 | Natural stones - Determination of resistance to ageing by salt mist |
| UNI EN 14303 par. 4.3.2 | Thermal insulation products for building - Maximum service temperature |
| UNI EN 14303 par. 4.3.3 | Thermal insulation products for building - Minimum service temperature |
| UNI EN 14303 par.4.2.2.1 | Thermal insulation products for building - Linear dimensions |
| UNI EN 1464 | Adhesives - Peel resistance of adhesive bonds - floating roller method |
| UNI EN 1465 | Adhesives - Tensile lap-shear strength bonded assemblies |
| UNI EN 14901-1 | Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 1: Epoxy coating (heavy duty) |
| UNI EN 14901-1 Par 7.2.2 | Resilience test - Impact test |
| UNI EN 14901-1 Par 7.2.3 | Penetrration resistance |
| UNI EN 14901-1 Par 7.2.4 | Non-Pourosity check |
| UNI EN 14901-1 Par 7.2.5.1 | Hot air aging resistance |
| UNI EN 14901-1 Par 7.2.5.2 | Hot water aging resistance |
| UNI EN 14901-2 | Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 2: Thermoplastic acid modified polyolefin coating (TMPO) |
| UNI EN 1504-2 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete |
| UNI EN 15136 | Restrizioni su materiali ed oggetti definiti nell Allegato II del Reg.10-2011-UE e smi - BADGE(cas1675-54-3)+derivati, BFDGE(cas 39817-09-9)e NOGE(altri glicidil-eteri novolac) -Migrazione Specifica (mg-kg) BADGE.H2O(cas76002-91-0) BADGE.2H2O(cas76002-91-0) BADGE.HCl(cas13836-48-1) BADGE.2HCl(cas4809-35-2) BADGE.H2O.HCl(cas227947-06-0) |
| UNI EN 15189 | Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods |
| UNI EN 15309 | Determination of elemental composition by X-ray fluorescence |
| UNI EN 15336 | Adhesives - Tensile lap-shear strength bonded assemblies |
| UNI EN 15340 | Thermal spraying - Determination of shear load resistance of thermally sprayed coatings |
| UNI EN 1542 | Products and systems for the protection and repair of concrete structures - Measurement of bond strength by pull-off |
| UNI EN 15457 | Paints and varnishes - Laboratory method for testing the efficacy of film preservatives in a coating against fungi |
| UNI EN 15458 | Paints and varnishes - Laboratory method for testing the efficacy of film preservatives in a coating against algae |
| UNI EN 1568-3 Annex D | Specification for low expansion foam concentrates dor surface application to water-immiscible liquids - Viscosity |
| UNI EN 15976 | Flexible sheets for waterproofing - Determination of emissivity |
| UNI EN 1606 | Thermal insulating products for building applications - Determination of compressive creep |
| UNI EN 1607 | Thermal insulating products for building applications - Determination of tensile strength |
| UNI EN 17036 | Conservation of Cultural Heritage - Artificial ageing by simulated solar radiation of the surface of untreated or treated porous inorganic materials |
| UNI EN 1849 | Flexible sheets for waterproofing - Determination of thickness and mass per unit area - Part 2: Plastics and rubber sheets for roof waterproofing |
| UNI EN 1928 | Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets - Determination of watertightness |
| UNI EN 2155-5 | Aerospace series - Test methods for transparent materials for aircraft glazing - Determination of visible light transmission |
| UNI EN 23270 | Paints and varnishes and their raw materials - Temperatures and humidities for conditioning and testing |
| UNI EN 253 par. 4.3.1.1 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Carbon black content and distribution |
| UNI EN 253 par. 4.3.1.2 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Melt mass flow rate |
| UNI EN 253 par. 4.3.1.3 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Thermal stability |
| UNI EN 253 par. 4.3.2.2 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Wall thickness |
| UNI EN 253 par. 4.3.2.4 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Elongation at break |
| UNI EN 253 par. 4.3.2.6 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Stress Crack Resistance |
| UNI EN 253 par. 4.4.2.2 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Cell size |
| UNI EN 253 par. 4.4.2.3 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Closed cell content |
| UNI EN 253 par. 4.4.3 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Compressive Strenght |
| UNI EN 253 par. 4.4.4 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Foam Density |
| UNI EN 253 par. 4.4.5 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Water Absorption at elevated temperature |
| UNI EN 253 par. 4.5.7 | Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Thermal conductivity in unaged condition |
| UNI EN 253 par. 5.4.1 | District heating pipes - Bonded single pipe systems for directly buried hot water networks - Factory made pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Axial shear strength |
| UNI EN 3475-303 | Aerospace series - Cables, electrical, aircraft use - Part 303: Insulation resistance |
| UNI EN 3475-405 | Aerospace series - Cables, electrical, aircraft use - Part 405: Bending at ambient temperature |
| UNI EN 3475-410 | Aerospace series - Cables, electrical, aircraft use - Part 410: Thermal endurance |
| UNI EN 3475-510 | Aerospace series - Cables, electrical, aircraft use - Test methods - Tensile strength and elongation of extruded insulation, sheath and jacket material |
| UNI EN 3665 | Aerospace series - Test methods for paints and varnishes - Filiform corrosion resistance test on aluminium alloys |
| UNI EN 4170 | Aerospace series - Paints and varnishes - Test method for measurement of resistance to cold crack temperature cycle |
| UNI EN 479 | Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of heat reversion |
| UNI EN 489-1 par.5.3 | Water tightness test |
| UNI EN 61 | Glass reinforced plastics - Determination of tensible properties |
| UNI EN 681-1 | Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber |
| UNI EN 728 | Plastics piping and ducting systems - Polyolefin Pipes And Fittings |
| UNI EN ISO 10147 | Pipes and fittings made of crosslinked polyethylene (PE-X) - Estimation of the degree of crosslinking by determination of the gel content |
| UNI EN ISO 10456 | Building materials and products - Hygrothermal properties -- Tabulated design values and procedures for determining declared and design thermal values |
| UNI EN ISO 105-A05 | Tests for colour fastness - Instrumental assessment of change in colour for determination of grey scale rating |
| UNI EN ISO 105-B02 | Textiles - Colour fastness to artificial light: Xenon arc fading lamp test |
| UNI EN ISO 105-B06 | Textiles - Colour fastness and ageing to artificial light (xenon) at high temperatures |
| UNI EN ISO 105-E01 | Textiles - Colour fastness to water |
| UNI EN ISO 105-X12 | Textiles - Colour fastness to rubbing |
| UNI EN ISO 10619-1 | Rubber and plastics hoses and tubing - Bending test at ambient temperature |
| UNI EN ISO 11127-2 | Test methods for non-metallic blast-cleaning abrasives - Determination of particle size distribution |
| UNI EN ISO 11127-3 | Test methods for non-metallic blast-cleaning abrasives - Determination of apparent density |
| UNI EN ISO 11127-4 | Test methods for non-metallic blast-cleaning abrasives - Assessment of hardness by a glass slide test |
| UNI EN ISO 11127-5 | Test methods for non-metallic blast-cleaning abrasives - Determination of moisture |
| UNI EN ISO 11127-6 | Test methods for non-metallic blast-cleaning abrasives - Determination of water-soluble contaminants by conductivity measurement |
| UNI EN ISO 11127-7 | Test methods for non-metallic blast-cleaning abrasives - Determination of water-soluble chlorides |
| UNI EN ISO 1133-1 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics |
| UNI EN ISO 1133-2 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 2: Method for materials sensitive to time-temperature history and-or moisture |
| UNI EN ISO 11339 | Adhesives - T-peel test for flexible-to-flexible bonded assemblies |
| UNI EN ISO 11357-1 | Plastics - Differential scanning calorimetry (DSC) |
| UNI EN ISO 11357-2 | Plastics - Differential scanning calorimetry (DSC) - Part 2: Determination of glass transition temperature and step height |
| UNI EN ISO 11357-3 | Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization |
| UNI EN ISO 11357-4 | Plastics - Determination of specific heat capacity |
| UNI EN ISO 11357-6 | Plastics - Differential scanning calorimetry (DSC) |
| UNI EN ISO 11358-1 | Plastics - Thermogravimetry (TG) of polymers |
| UNI EN ISO 1158 | Plastics - Determination of chlorine content |
| UNI EN ISO 11664-4 | Colorimetry - CIE 1976 colour space |
| UNI EN ISO 11667 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of resin, reinforced-fibre and mineral-filler content - Dissolution methods (ISO 11667:1997) |
| UNI EN ISO 1167-1 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| UNI EN ISO 1172 | Textile-glass and mineral-filler content |
| UNI EN ISO 1183-1 - Met. B | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Liquid pycnometer |
| UNI EN ISO 1183-1 - Met.A | Plastics - Methods for determining the density of non-cellular plastics |
| UNI EN ISO 1183-3 | Plastics - Gas pyknometer method |
| UNI EN ISO 11890-1 | Paints and varnishes - Determination of volatile organic compound (VOC) content - Part 1: Difference method (ISO 11890-1:2007) |
| UNI EN ISO 11890-2 | Paints and varnishes - Determination of volatile organic compounds(VOC) and-or semi volatile organic compounds (SVOC) content - Part 2: Gas-chromatographic method (ISO 11890-2:2020) |
| UNI EN ISO 11909 | Binders for paints and varnishes - Polyisocyanate resins - General methods of test (ISO 11909:2007) |
| UNI EN ISO 11997-1 | Paint and varnish - Resistance to cyclic corrosion conditions - Wet (salt fog)-Dry-Humidity |
| UNI EN ISO 11997-2 | Paints and varnishes - Wet (salt fog)-dry-humidity-UV light |
| UNI EN ISO 11998 | Paints and varnishes - Determination of wet-scrub resistance and cleanability of coatings |
| UNI EN ISO 12236 | Geosynthetics - Static puncture test (CBR test) |
| UNI EN ISO 13468-1 | Plastics - Determination of the total luminous transmittance of transparent materials |
| UNI EN ISO 13468-2 | Plastics - Determination of the total luminous transmittance of transparent materials |
| UNI EN ISO 13732-1 par.5.4 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces - Surface measurements |
| UNI EN ISO 13803 | Paints and varnishes - Determination of haze on paint films at 20 degrees |
| UNI EN ISO 13937-2 | Textiles - Tear properties of fabrics - Part 2: Determination of tear force of trouser-shaped test specimens (Single tear method) (ISO 13937-2:2000) |
| UNI EN ISO 14125 | Fibre-reinforced plastic composites - Determination of flexural properties |
| UNI EN ISO 14130 | Fibre-reinforced plastic composites - Determination of apparent interlaminar shear strength by short-beam method |
| UNI EN ISO 1463 | Measurement of coating thickness - Microscopical method |
| UNI EN ISO 14680-2 | Paints and varnishes - Determination of pigment content |
| UNI EN ISO 14713-1 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance |
| UNI EN ISO 14713-2 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing |
| UNI EN ISO 148-1 | Metallic materials - Charpy pendulum impact test |
| UNI EN ISO 14916 | Thermal spraying - Determination of tensile adhesive strength |
| UNI EN ISO 14918 | Thermal spraying - Qualification testing of thermal sprayers |
| UNI EN ISO 14919 | Thermal spraying -- Wires, rods and cords for flame and arc spraying - Classification -- Technical supply conditions |
| UNI EN ISO 15091 | Paints and varnishes - Determination of electrical conductivity and resistance (ISO 15091:2020) |
| UNI EN ISO 15110 | Paints and varnishes - Artificial weathering including acidic deposition |
| UNI EN ISO 1513 | Paints and varnishes - Examination and preparation of test samples |
| UNI EN ISO 15184 | Paints and varnishes - Film hardness by pencil test |
| UNI EN ISO 1519 | Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011) |
| UNI EN ISO 1520 | Paints and varnishes - Cupping test |
| UNI EN ISO 1522 | Paints and varnishes - Pendulum damping test |
| UNI EN ISO 1524 | Paints, varnishes and printing inks - Determination of fineness of grind |
| UNI EN ISO 15512 | Plastics - Determination of water content |
| UNI EN ISO 16276-2 | Paint systems - Cross-cut testing and X-cut testing |
| UNI EN ISO 16474-1 | Paints and varnishes - Methods of exposure to laboratory light sources |
| UNI EN ISO 16474-2 | Paints and varnishes - Methods of exposure to laboratory light sources |
| UNI EN ISO 16474-3 UV | Paints and varnishes - Methods of exposure to laboratory light sources |
| UNI EN ISO 16703 | Soil quality - Determination of content of hydrocarbon in the range C10 to C40 by gas chromatography |
| UNI EN ISO 16773-1 | Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 1: Terms and definitions (ISO 16773-1:2016) |
| UNI EN ISO 16773-2 | Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 2: Collection of data (ISO 16773-2:2016) |
| UNI EN ISO 16773-3 | Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 3: Processing and analysis of data from dummy cells (ISO 16773-3:2016) |
| UNI EN ISO 16773-4 | Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 4: Examples of spectra of polymer-coated and uncoated specimens (ISO 16773-4:2017) |
| UNI EN ISO 16925 | Paints and varnishes - Determination of the resistance of coatings to pressure water-jetting (ISO 16925:2014) |
| UNI EN ISO 17226-1 | Leather - Chemical determination of formaldehyde content - Part 1: Method using high-performance liquid chromatography |
| UNI EN ISO 17463 | Paints and varnishes - Guidelines for the determination of anticorrosive properties of organic coatings by accelerated cyclic electrochemical technique (ISO 17463:2014) |
| UNI EN ISO 175 | Plastics - Determination of the effects of immersion in liquid chemicals |
| UNI EN ISO 178 | Plastics - Determination of flexural properties |
| UNI EN ISO 17872 | Paints and varnishes - Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing |
| UNI EN ISO 179-1 | Plastics - Determination of Charpy impact properties - Part 1 |
| UNI EN ISO 179-2 | Plastics - Determination of Charpy impact properties Instrumented impact test |
| UNI EN ISO 180 | Plastics - Determination of Izod impact strength |
| UNI EN ISO 1923 | Cellular plastics and rubbers - Determination of linear dimensions |
| UNI EN ISO 19403-1 | Paints and varnishes - Terminology and general principles |
| UNI EN ISO 19403-2 | Wettability - Part 2: Determination of the surface free energy of solid surfaces by measuring the contact angle |
| UNI EN ISO 19403-3 | Wettability - Part 3: Determination of the surface tension of liquids using the pendant drop method (ISO 19403-3:2017) |
| UNI EN ISO 19403-4 | Wettability - Part 4: Determination of the polar and dispersive fractions of the surface tension of liquids from an interfacial tension (ISO 19403-4:2017) |
| UNI EN ISO 19403-5 | Wettability - Part 5: Determination of the polar and dispersive fractions of the surface tension of liquids from contact angles measurements on a solid with only a disperse contribution to its surface energy (ISO 19403-5:2017) |
| UNI EN ISO 19403-6 | Wettability - Part 6: Measurement of dynamic contact angle (ISO 19403-6:2017) |
| UNI EN ISO 2039-1 | Plastics - Determination of hardness |
| UNI EN ISO 20482 | Metallic materials - Sheet and strip - Erichsen cupping test (ISO 20482:2013) |
| UNI EN ISO 20566 | Paints and varnishes - Determination of the scratch resistance of a coating system using a laboratory-scale car-wash |
| UNI EN ISO 20567-1 | Paints and varnishes - Determination of stone-chip resistance of coatings |
| UNI EN ISO 20567-2 | Paints and varnishes - Determination of stone-chip resistance of coatings Single-impact test with a guided impact body |
| UNI EN ISO 2063-2 | Thermal spraying — Zinc, aluminium and their alloys - Part 2: Execution of corrosion protection systems |
| UNI EN ISO 21546 | Paints and varnishes - Determination of the resistance to rubbing using a linear abrasion tester (crockmeter) |
| UNI EN ISO 2160 | Petroleum products - Corrosiveness to copper - Copper strip test |
| UNI EN ISO 2178 | Non-magnetic coatings on magnetic substrates - Measurement of coating thickness |
| UNI EN ISO 21809-1 Annex A | External coatings for buried or submerged pipelines used in pipeline transportation systems - Thicknesses of the coating |
| UNI EN ISO 21809-1 Annex B | Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems Polyolefin coatings (3-layer PE and 3-layer PP) - Holiday detection test |
| UNI EN ISO 21809-1 Annex C | External coatings for buried or submerged pipelines used in pipeline transportation systems - Peel strenght test |
| UNI EN ISO 21809-1 Annex D | External coatings for buried or submerged pipelines used in pipeline transportation systems - Thermal analysis of epoxy and cured epoxy coating film with Tg<115.C |
| UNI EN ISO 21809-1 Annex E | External coatings for buried or submerged pipelines used in pipeline transportation systems - Impact strenght |
| UNI EN ISO 21809-1 Annex F | External coatings for buried or submerged pipelines used in pipeline transportation systems - Indentation test |
| UNI EN ISO 21809-1 Annex G.1 | Polyolefin coatings (3-layer PE and 3-layer PP) - UV ageing |
| UNI EN ISO 21809-1 Annex G.2 | Polyolefin coatings (3-layer PE and 3-layer PP) - Thermal ageing |
| UNI EN ISO 21809-1 Annex H | External coatings for buried or submerged pipelines used in pipeline transportation systems - Cathodic disbondment test |
| UNI EN ISO 21809-1 Annex I | External coatings for buried or submerged pipelines used in pipeline transportation systems - Flexibility test |
| UNI EN ISO 21809-1 Annex J | External coatings for buried or submerged pipelines used in pipeline transportation systems - Gel time of epoxy powder |
| UNI EN ISO 21809-1 Annex K | External coatings for buried or submerged pipelines used in pipeline transportation systems - Moisture content |
| UNI EN ISO 21809-1 Annex L | Hot water immersion test |
| UNI EN ISO 21809-1 Annex M | External coatings for buried or submerged pipelines used in pipeline transportation systems - Density of epoxy powder |
| UNI EN ISO 21809-2 par. A.10 | Single layer fusion-bonded epoxy coatings - Cathodic disbondment of high temperature coatings ( >95°C) |
| UNI EN ISO 21809-2 par. A.11 | Single layer fusion-bonded epoxy coatings - Interface contamination |
| UNI EN ISO 21809-2 par. A.12 | Single layer fusion-bonded epoxy coatings - Cross section and Interface porosity |
| UNI EN ISO 21809-2 par. A.13 | Single layer fusion-bonded epoxy coatings - Flexibility of the coating |
| UNI EN ISO 21809-2 par. A.14 | Single layer fusion-bonded epoxy coatings - Resistance to impact of the coating |
| UNI EN ISO 21809-2 par. A.15 | Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems Single layer fusion-bonded epoxy coatings - Cathodic disbondment of strained coating |
| UNI EN ISO 21809-2 par. A.16 | Single layer fusion-bonded epoxy coatings - Hot-water adhesion of the coating |
| UNI EN ISO 21809-2 par. A.2 | Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems - Single layer fusion-bonded epoxy coatings - Cure time of the epoxy powder |
| UNI EN ISO 21809-2 par. A.3 | Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems - Single layer fusion-bonded epoxy coatings - Gel time of the epoxy powder |
| UNI EN ISO 21809-2 par. A.4 | Single layer fusion-bonded epoxy coatings - Dry adhesion test |
| UNI EN ISO 21809-2 par. A.5 | Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems - Single layer fusion-bonded epoxy coatings - Total volatile-moisture content of the epoxy powder — Mass loss - Procedure A |
| UNI EN ISO 21809-2 par. A.6 | Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems Single layer fusion-bonded epoxy coatings - Particle size of the epoxy powder |
| UNI EN ISO 21809-2 par. A.7 | Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems - Single layer fusion-bonded epoxy coatings - Density of the epoxy powder |
| UNI EN ISO 21809-2 par. A.8 | Single layer fusion-bonded epoxy coatings - Thermal analysis of epoxy powder and cured coating film |
| UNI EN ISO 21809-2 par. A.9 | Single layer fusion-bonded epoxy coatings - Cathodic disbondment of coatings for standard temperatures up to 95°C |
| UNI EN ISO 21809-3 Annex B | Field joint coatings - Inspection of thickness |
| UNI EN ISO 21809-3 Annex C | Field joint coatings - Holiday detection test |
| UNI EN ISO 21809-3 Annex D | Field joint coatings - Impact test |
| UNI EN ISO 21809-3 Annex E | Field joint coatings - Indentation test |
| UNI EN ISO 21809-3 Annex F | Field joint coatings - Specific electrical Insulation resistance |
| UNI EN ISO 21809-3 Annex G | Field joint coatings - Cathodic disbondment test |
| UNI EN ISO 21809-3 Annex H | Field Joint coatings - Peel strenght |
| UNI EN ISO 21809-3 Annex I | Field joint coatings - Hot water immersion test |
| UNI EN ISO 21809-3 Annex J | Field joint coatings - Lap shear strenght |
| UNI EN ISO 21809-3 Annex M | Thermal ageing resistance |
| UNI EN ISO 21809-3 Annex P | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings - Amendment 1: Introduction of mesh-backed coating systems - Thermal analysis of epoxy powder and cured epoxy film FBE |
| UNI EN ISO 21809-3 Annex Q | Field Joint Coatings - Resistance to removal |
| UNI EN ISO 21920-2 | Surface texture: Profile |
| UNI EN ISO 21920-3 | Geometrical product specifications (GPS) - Surface texture: Profile - Specification operators |
| UNI EN ISO 22032 | Water quality - Determination of selected polybrominated diphenyl ethers in sediment and sewage sludge - Method using extraction and gas chromatography-mass spectrometry |
| UNI EN ISO 22088-2 | Plastics - Determination of resistance to environmental stress cracking (ESC) Constant tensile load method |
| UNI EN ISO 22088-3 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 3: Bent strip method |
| UNI EN ISO 22479 | Corrosion of metals and alloys - Sulfur dioxide test in a humid atmosphere (fixed gas method) |
| UNI EN ISO 22557 | Paints and varnishes - Scratch test using a spring-loaded pen |
| UNI EN ISO 22631 | Adhesives - Peel test |
| UNI EN ISO 22775 | Footwear - Corrosion resistance |
| UNI EN ISO 2360 | Non-conductive coatings on non-magnetic electrically conductive basis materials - Measurement of coating thickness |
| UNI EN ISO 2409 | Paints and varnishes on metallic substrate - Cross-cut test |
| UNI EN ISO 2507-1 | Thermoplastics pipes and fittings - Vicat softening temperature - Part 1: General test method |
| UNI EN ISO 2555 | Plastics -- Resins in the liquid state or as emulsions or dispersions - Determination of apparent viscosity using a single cylinder type rotational viscometer method |
| UNI EN ISO 2592 | Petroleum products - Flash point |
| UNI EN ISO 2808 | Paints and varnishes on metallic substrate - Determination of film thickness |
| UNI EN ISO 2811-1 | Paints and varnishes - Determination of density |
| UNI EN ISO 2811-2 | Paints and varnishes - Determination of density |
| UNI EN ISO 2812-1 | Paints and varnishes on metallic substrate - Determination of resistance to liquids |
| UNI EN ISO 2812-2 | Paints and varnishes on metallic substrate - Determination of resistance to liquids |
| UNI EN ISO 2812-3 | Paints and varnishes - Determination of resistance to liquids - Part 3 Method using an absorbent medium |
| UNI EN ISO 2812-4 | Paints and varnishes - Determination of resistance to liquids |
| UNI EN ISO 2812-5 | Paints and varnishes - Determination of resistance to liquids Temperature-gradient oven method |
| UNI EN ISO 2813 | Paints and varnishes - Determination of gloss value at 20 degrees, 60 degrees and 85 degrees |
| UNI EN ISO 2819 | Metallic coatings on metallic substrates - Electrodeposited and chemically deposited coatings |
| UNI EN ISO 2884-2 | Paints and varnishes - Disc or ball viscometer operated at a specified speed |
| UNI EN ISO 294-4 | Determination of moulding shrinkage |
| UNI EN ISO 29601 | Varnishes - Porosity in a dry film |
| UNI EN ISO 29862 | Self adhesive tapes - Determination of peel adhesion properties |
| UNI EN ISO 3016 | Petroleum and related products from natural or synthetic sources - Determination of pour point |
| UNI EN ISO 306 | Plastics - Determination of Vicat softening temperature |
| UNI EN ISO 307 | Plastics - Polyamides - Determination of viscosity number |
| UNI EN ISO 3104 | Determination of kinematic viscosity and calculation of dynamic viscosity |
| UNI EN ISO 3231 | Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide |
| UNI EN ISO 3233-1 | Paints and varnishes - Determination of percentage volume of non-volatile matter - Part 1: Method using a coated test panel to determine non-volatile matter and to determine dry-film density by the Archimedes principle (ISO 3233-1:2019) |
| UNI EN ISO 3233-2 | Paints and varnishes - Method using the determination of non-volatile-matter content and determination of dry film density |
| UNI EN ISO 3248 | Paints and varnishes -- - Determination of the effect of heat |
| UNI EN ISO 3251 | Paints, varnishes e plastics - Determination of non-volatile-matter content |
| UNI EN ISO 3386-1 | Determination of stress-strain characteristics in compression |
| UNI EN ISO 3451-1 | Plastics - Determination of ash General methods |
| UNI EN ISO 3611 | Geometrical product specifications (GPS) - Dimensional measuring equipment: Micrometers for external measurements - Design and metrological characteristics |
| UNI EN ISO 3651-2 | Determinazione della resistenza alla corrosione intergranulare degli acciai inossidabili - Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in media containing sulfuric acid (ISO 3651-2:1998) |
| UNI EN ISO 3679 | Determination of flash point - Method for flash no-flash and flash point by small scale closed cup tester |
| UNI EN ISO 3696 | Water for analytical laboratory use |
| UNI EN ISO 3915 | Plastics - Measurements of resistivity of conductive plastics |
| UNI EN ISO 4623-1 | Paints and varnishes - Determination of resistance to filiform corrosion Steel substrates |
| UNI EN ISO 4624 | Paints and varnishes on metallic substrate - Pull-off test for adhesion |
| UNI EN ISO 4628-1 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance |
| UNI EN ISO 4628-10 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance |
| UNI EN ISO 4628-2 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance |
| UNI EN ISO 4628-3 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects and of intensity of uniform changes in appearance |
| UNI EN ISO 4628-4 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance |
| UNI EN ISO 4628-5 | Paints and varnishes - Assessment of degree of flaking |
| UNI EN ISO 4628-6 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance |
| UNI EN ISO 4628-7 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance |
| UNI EN ISO 4628-8 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance |
| UNI EN ISO 4629-1 | Binders for paints and varnishes - Determination of hydroxyl value - Part 1: Titrimetric method without using a catalyst (ISO 4629-1:2016) |
| UNI EN ISO 489 | Plastics - Determination of refractive index |
| UNI EN ISO 4892-1 | Plastics - Methods of exposure to laboratory light sources |
| UNI EN ISO 4892-2 | Plastics - Methods of exposure to laboratory light sources |
| UNI EN ISO 4892-3 | Plastics - Methods of exposure to laboratory light sources |
| UNI EN ISO 527-1 | Plastics - Determination of tensile properties |
| UNI EN ISO 527-2 | Plastics - Determination of tensile properties |
| UNI EN ISO 527-3 | Plastics - Tensile properties - test conditions for films and sheets |
| UNI EN ISO 527-4 COMPOSITI | Plastics - Determination of tensile properties Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| UNI EN ISO 580 | Plastics piping and ducting systems - njection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating |
| UNI EN ISO 60 | Apparent density of material |
| UNI EN ISO 604 | Plastics - Determination of compressive properties |
| UNI EN ISO 62 | Plastics - Determination of water absorption |
| UNI EN ISO 6259-1 | Thermoplastics pipes - Determination of tensile properties |
| UNI EN ISO 6259-2 | Pipes made of PVC - Determination of tensile properties |
| UNI EN ISO 6259-3 | Polyolefin pipes - Determination of tensile properties |
| UNI EN ISO 6270-1 | Paints and varnishes - Determination of resistance to humidity |
| UNI EN ISO 6270-2 | Paints and varnishes on metallic substrate - Determination of resistance to humidity |
| UNI EN ISO 6272-1 | Paints and varnishes - Rapid-deformation (impact resistance) tests |
| UNI EN ISO 6272-2 | Paints and varnishes - Rapid-deformation (impact resistance) tests |
| UNI EN ISO 6504-1 | Paints and varnishes - Determination of hiding power — Part 1: Kubelka-Munk method |
| UNI EN ISO 6506-1 | Metallic materials - Brinell hardness |
| UNI EN ISO 6507-1 | Metallic materials - Vickers hardness test |
| UNI EN ISO 6508-1 | Metallic materials - Rockwell hardness test |
| UNI EN ISO 6509-1 | Corrosion of metals and alloys - Dezincification resistance of copper alloys with zinc |
| UNI EN ISO 6860 | Paints and varnishes - Bend test (conical mandrel) |
| UNI EN ISO 6892-1 | Metallic materials - Tensile testing - Method of test at room temperature |
| UNI EN ISO 6892-2 | Metallic materials - Tensile testing — Part 2: Method of test at elevated temperature |
| UNI EN ISO 6892-3 | Metallic materials - Tensile testing — Part 3: Method of test at low temperature |
| UNI EN ISO 6946 | Building components and building elements - Thermal resistance and thermal transmittance — Calculation methods |
| UNI EN ISO 7599 par.6.3 | Anodizing of aluminium and its alloys - General specifications for anodic oxidation coatings on aluminium |
| UNI EN ISO 7783 | Paints and varnishes - Determination of water-vapour transmission properties — Cup method |
| UNI EN ISO 7784-1 | Paints and varnishes - Determination of resistance to abrasion — Part 1: Method with abrasive-paper covered wheels and rotating test specimen |
| UNI EN ISO 7784-2 | Paints and varnishes - Determination of resistance to abrasion |
| UNI EN ISO 80079-36 | Surface resistance test of non-conductive parts of the equipment relevant for explosion prevention and protection |
| UNI EN ISO 8031 | Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2020) |
| UNI EN ISO 8130-1 | Coating powders - Part 1: Determination of particle size distribution by sieving |
| UNI EN ISO 8130-6 | Coating powders - Part 6: Determination of gel time of thermosetting coating powders at a given temperature |
| UNI EN ISO 8256 | Plastics - Determination of tensile-impact strength |
| UNI EN ISO 8295 | Plastics - Film and sheeting - Determination of the coefficients of friction |
| UNI EN ISO 8407 | Corrosion of metals and alloys - Removal of corrosion products from corrosion test specimens |
| UNI EN ISO 844 | Rigid cellular plastics - Determination of compression properties |
| UNI EN ISO 845 | Cellular plastics and rubbers - Determination of apparent density |
| UNI EN ISO 8497 | Thermal insulation - Determination of steady-state thermal transmission properties of thermal insulation for circular pipes |
| UNI EN ISO 8502-4 | Preparation of steel substrates before application of paint and related products - Tests for the assessment of surface cleanliness |
| UNI EN ISO 8502-9 | Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness |
| UNI EN ISO 8503-3 | Surface roughness characteristics of blast-cleaned steel substrates - Part 3: Method for the determination of surface profile - Focusing microscope procedure |
| UNI EN ISO 8503-4 | Preparation of steel substrates before application of paints and related products - Part 4: Stylus instrument procedure |
| UNI EN ISO 8510-2 | Adhesives - Peel test for a flexible-bonded-to-rigid test specimen assembly - 180 degree peel |
| UNI EN ISO 868 | Plastics and ebonite - Determination of indentation hardness by means of a durometer |
| UNI EN ISO 8985 | Plastics - Ethylene-vinyl acetate copolymer (EVAC) thermoplastics - Determination of vinyl acetate content |
| UNI EN ISO 9073-5 | Textiles — Test methods for nonwovens - Part 5: Determination of resistance to mechanical penetration (ball burst procedure) |
| UNI EN ISO 9117-3 | Paints and varnishes - Drying tests - Part 3: Surface-drying test using ballotini |
| UNI EN ISO 9227 | Organic and inorganic coatings on metallic substrate - Corrosion tests in artificial atmospheres |
| UNI EN ISO 9227 - Acetica (AASS) | Anodic and organic coatings on aluminium - Corrosion in acetic acid salt spray (AASS) |
| UNI EN ISO 9227 - Cupro acetica (CASS) | Anodic and organic coatings on aluminium - Copper-acetic salt spray tests (CASS) |
| UNI EN ISO 9653 | Adhesives - Shear impact strength of adhesive bonds |
| UNI EN ISO 9712 | Non-destructive testing - Qualification and certification of NDT personnel |
| UNI EN ISO ISO 13934-1 | Textiles - Tensile properties of fabrics - Determination of maximum force and elongation at maximum force using the strip method |
| UNI EN ISO/CIE 11664-6 | Colorimetry - Part 6: CIEDE2000 colour-difference formula |
| UNI ISO 1817 | Rubber vulcanized or thermoplastic - Determination of the effect of liquids |
| UNI ISO 188 | Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests |
| UNI ISO 23529 | Rubber - General procedures for preparing and conditioning test pieces for physical test methods |
| UNI ISO 2878 | Rubber, vulcanized or thermoplastic — Antistatic and conductive products - Determination of electrical resistance |
| UNI ISO 3795 | Road vehicles and tractors and machinery for agriculture and forestry. - Determination of burning behaviour of interior materials. |
| UNI ISO 4650 | Identification - Infrared spectrometric methods |
| UNI ISO 48-2 | Determination of hardness |
| UNI ISO 7743 | Rubber, vulcanized or thermoplastic - Determination of compression stress-strain properties |
| UNI ISO 815-1 | Rubber, vulcanized or thermoplastic - Determination of compression set At ambient or elevated temperatures |
| UNI ISO 815-2 | Rubber, vulcanized or thermoplastic - Determination of compression set - Part 2: At low temperatures |
| VCS 1027, 1449 | Accelerated corrosion test, version II – ACT II |
| VDA 237-300 par. 5 tab. 2 | Surface protection brake calipers - Thermal shock |
| VDA 238-100 | Metallic materials - Plate bending test for metallic materials |
| VDA 270 | Leather - Determination of the odour characteristics |
| VDA 275 | Determination of formaldehyde release |
| VDA 278 | Thermal Desorption Analysis of Organic Emissions |
| VDA 621-415 | Paint and varnish - Cyclic corrosion |
| Volvo STD 1026,8177 | Chemical resistance |
| Volvo STD 104-0001 | Flammability |
| Volvo STD 422-0004 | Resistance to shortduration contact with fluids |
| Volvo STD 422-0006 | Resistance to short-duration contact with fluids |
| Volvo STD 423-0019 | Car-wash mar-resistance for topcoats |
| Volvo STD 423-0030 | Scratch resistance, Erichsen pen |
| Volvo STD 423-0036 | Impact strength, falling-weight method |
| Volvo STD 423-0037 | Colour fastness to rubbing |
| Volvo STD 423-0055 | Short-term heat resistance |
| Volvo TR EXTERIOR PLASTIC 24725236 par.2.1.5.1 | Moisture resistance - Ageing - Test |
| VW 44045 No.1.1 | Stabilization |
| VW 44045 No.10.1 | Flexural strength |
| VW 44045 No.10.2 | Flexural strength |
| VW 44045 No.11 | Impact strength |
| VW 44045 No.12 | Notched impact strength |
| VW 44045 No.13.1 | High-temperature behavior (90±2°C) |
| VW 44045 No.13.2 | High-temperature behavior (110±2°C) |
| VW 44045 No.14 | Low-temperature behavior |
| VW 44045 No.15 | Lightfastness |
| VW 44045 No.16 | Xenon arc light aging to determine tack |
| VW 44045 No.17 | Weathering in dry, hot climate as per PV 3929 |
| VW 44045 No.18 | Weathering in humid, hot climate as per PV 3930 |
| VW 44045 No.19 | Aging resistance |
| VW 44045 No.20 | Scratch resistance |
| VW 44045 No.21 | Mar resistance |
| VW 44045 No.22 | Stress whitening behavior as per PV 3966 |
| VW 44045 No.4 | Color |
| VW 44045 No.5 | Density |
| VW 44045 No.6 | Melting temperature |
| VW 44045 No.7 | Ignition residue |
| VW 44045 No.8 | Yield stress |
| VW 44045 No.9 | Tensile strength upon fracture |
| VW 50136 | PBT for Finished Parts Outside the Vehicle Interior |
| VW 50180 | Components, Semi-Finished Products and Materials in the Vehicle Interior - Emission Behavior |
| VW 50181 | Lights with transparent covering pane - Fogging characteristics |
| VW 50195 | Automobile Paint Coatings - Colorimetric Evaluation |
| VW 50196 | Colour and Gloss |
| VW 80000 K-06 | Electric and Electronic Components in Motor Vehicles up to 3.5 t - K-06 Salt spray test with operation, exterior |
| VW 80195 par.5.6 | Pressure washer test |
| VW 96150 par. 5.1 | Plastics and Adhesives - Specific volume resistance |
| VW PV 1015 par.3.3 | Specific Volume Resistance Testing |
| VW PV 1200 | Paints and varnishes - Testing of Resistance to Environmental Cycle Test (+80--40)°C |
| VW PV 1209 | Corrosion Test (Environmental Corrosion Cycle Test) |
| VW PV 1210 | Body and Add-On Parts/Hang-On Parts - Cyclic corrosion Test |
| VW PV 1303 | Xenon Arc Light Aging of Vehicle Interior Components |
| VW PV 1306 | Determining the Tackiness of Polypropylene Parts |
| VW PV 1503 | Paint and coatings - Pressure washer test |
| VW PV 2005 | Paints and varnishes - Testing of resistance to enviromental cycle test |
| VW PV 2044 KL1 | KL1 - Heat aging at +90°C |
| VW PV 2044 KL3 | KL3 - Heat and humidity aging |
| VW PV 2044 KL4 | KL4 - Low-temperature aging |
| VW PV 2044 KWL1 | KWL1 - Hot, dry climate with cold exposure |
| VW PV 2044 KWL2 | KWL2 - Humid, warm climate |
| VW PV 2044 KWL3 | KWL3 - Environmental simulation without radiation influence |
| VW PV 3.3.3 | Paints and Varnishes - Scratch Resistance Testing of Clear Coats |
| VW PV 3015 | Fogging behaviour of materials used in the vehicle interior |
| VW PV 3341 | Non-metallic materials in automotive interior trim - Emissions of organic compounds |
| VW PV 3357 | Behavior on Flame Exposure with a Burner |
| VW PV 3900 | Vehicle Interior Components - Odor Test |
| VW PV 3905 | Organic materials - Ball drop test |
| VW PV 3929 | Non-Metallic Materials - Weathering in Dry, Hot Climate |
| VW PV 3930 | Non-Metallic Materials - Weathering in Humid, Hot Climate |
| VW PV 3942 | Products for the Vehicle Interior - Emission Behavior Using the DUT Chamber Method |
| VW PV 3952 | Scratch Resistance of Surfaces without Finish Treatment |
| VW PV 3964 | Testing of Cream Resistance |
| VW PV 3966 | Stress Whitening Properties (Ball Drop Test) |
| VW PV 3974 | Determination of the Mar resistance |
| VW PV 3983 | Plastics and Thermoplastic Elastomers - Testing Resistance to Agents in Conjunction with Mechanical Stresses |
| VW PV 3987 | Scrub Resistance |
| VW PV 3989 | Low-temperature behavior for plastic components - Ball drop test |
| VW TL 1010 | Materials for Vehicle Interiors - Burning Behavior |
| VW TL 1011 | Flammability of Non-Metallic Materials |
| VW TL 207 Tab.1 No.1 | Reflective Coatings on Enclosed Plastic Reflectors - PV 1200 - 8 cycles |
| VW TL 207 Tab.1 No.2 | Reflective Coatings on Enclosed Plastic Reflectors - Heat aging |
| VW TL 207 Tab.1 No.3 | Reflective Coatings on Enclosed Plastic Reflectors - ISO 6270-2 - 48h |
| VW TL 211 No. 1.1 | Gloss value |
| VW TL 211 No. 1.2.1 | Visual matching |
| VW TL 211 No. 1.2.2 | Colorimetric evaluation |
| VW TL 211 No. 1.3 | Wave-scan |
| VW TL 211 No. 2 | Coating thickness |
| VW TL 211 No. 3.1 | Stone impact test |
| VW TL 211 No. 3.2 | Steam-jet test |
| VW TL 211 No. 3.3 | Cross-cut test |
| VW TL 211 No. 3.4 | Resistance to humidity: degree of blistering and adhesion by steam-jet test and cross-cut test. |
| VW TL 211 No. 4.1 | Environmental cycle test |
| VW TL 211 No. 4.2 | Coating of Plastic Exterior Parts - Heat aging in a forced-air oven |
| VW TL 211 No. 5 | Corrosion resistance: 20 cycles as per PV1200, then 240h pf CASS - ISO 9227. |
| VW TL 211 No. 6.1 | Resistance to tunnel washes |
| VW TL 211 No. 7.1 | Resistance to chemicals: FAM test fuel |
| VW TL 211 No. 7.10 | Resistance to chemicals: artificial bird droppings |
| VW TL 211 No. 7.11 | Resistance to chemicals: Tree resine (ISO 2812-4 A.4.1) |
| VW TL 211 No. 7.12 | Cream resistance |
| VW TL 211 No. 7.2 | Resistance to chemicals: E10 gasoline |
| VW TL 211 No. 7.3 | Resistance to chemicals: B7 diesel fuel |
| VW TL 211 No. 7.4 | Resistance to chemicals: Isopropanol |
| VW TL 211 No. 7.5 | Resistance to chemicals: sodium hydroxide solution |
| VW TL 211 No. 7.6 | Resistance to chemicals: sulfuric acid |
| VW TL 211 No. 7.7 | Resistance to chemicals: 10 hydrochloric acid |
| VW TL 211 No. 7.8 | Resistance to chemicals: water (grade 3) |
| VW TL 211 No. 7.9 | Resistance to chemicals: nitrocellulose thinner |
| VW TL 211 No. 8.1.1 | Weathering in humid, hot climate as per PV 3930 - 1 year |
| VW TL 211 No. 8.1.2 | Weathering in dry, hot climate as per PV 3929 - 1 year |
| VW TL 211 No. 8.2.1 | Weathering in humid, hot climate as per PV 3930 - 2 years |
| VW TL 211 No. 8.2.2 | Weathering in dry, hot climate as per PV 3929 - 2 yeas |
| VW TL 212 par. 4.6.2 | Oxide Coatings on Aluminum Parts - Alkali resistance |
| VW TL 212 par. 4.7 | Oxide Coatings on Aluminum Parts - Thermal stability |
| VW TL 226 Tab2 Par 2.1 | Cross-cut test |
| VW TL 226 Tab2 Par 2.2 | Cross-cut test (St. Andrew cross) |
| VW TL 226 Tab2 Par 3 | Scratch resistance |
| VW TL 226 Tab2 Par 4.1 | Heat resistance in a drying oven |
| VW TL 226 Tab2 Par 4.2 | Paintwork on Materials of Vehicle Interior Equipment - Resistence to Environmental cycle as per Test Specification PV 1200 (-40°C-80°) |
| VW TL 226 Tab2 Par 5.1 | Resistence to humidity |
| VW TL 226 Tab2 Par 5.2 | Paintwork on Materials of Vehicle Interior Equipment - Lightfastness |
| VW TL 226 Tab2 Par 5.3 | Paintwork on Materials of Vehicle Interior Equipment - Hydrolysis aging |
| VW TL 226 Tab2 Par 6.1 | Abrasion behavior |
| VW TL 226 Tab2 Par 6.2 | Droplet test and Drying @60°C-30min - Storage 24h RT |
| VW TL 226 Tab2 Par 6.3 | Testing of Cream Resistance |
| VW TL 226 Tab2 Par 7 | Scrub resistance (micro-scratch resistance) of high-gloss surfaces |
| VW TL 227 par.3.10.1 | Corrosion cycle test |
| VW TL 227 par.3.10.2 | Condensation atmosphere with constant humidity |
| VW TL 227 par.3.11 | Resistance to chemicals |
| VW TL 227 par.3.7 | Coating thickness |
| VW TL 227 par.3.8 | Adhesion and brittleness |
| VW TL 227 par.3.9 | Stone-chip resistance |
| VW TL 256 No.10 | Impact test at low temperature |
| VW TL 256 No.11 | Resistance to chemicals |
| VW TL 256 No.6 | Coating adhesion (cross-cut test) |
| VW TL 256 No.7 | Stone-chip resistance |
| VW TL 256 No.8.1 | Corrosion cycle test (PV1210) |
| VW TL 256 No.8.2 | Condensation atmosphere with constant humidity |
| VW TL 256 No.9.1 | Heat aging |
| VW TL 256 No.9.2 | Low-temperature aging |
| VW TL 260 No.1.1 | Neutral salt spray test (NSS) |
| VW TL 260 No.1.2 | Corrosion cycle test as per PV1210 |
| VW TL 260 No.1.3 | Constant humidity (CH) as per DIN EN ISO 6270-2 |
| VW TL 260 No.2.10 | Resistance to chemicals - VW 50002 |
| VW TL 260 No.2.2 | Resistance to chemicals - FAM test fuel B |
| VW TL 260 No.2.3 | Resistance to chemicals - E10 gasoline |
| VW TL 260 No.2.4 | Resistance to chemicals - B7 diesel |
| VW TL 260 No.2.5 | Resistance to chemicals - Factory-fill engine oil |
| VW TL 260 No.2.6 | Resistance to chemicals - Central hydraulic system fluid |
| VW TL 260 No.2.7 | Resistance to chemicals - 10% sulfuric acid |
| VW TL 260 No.2.8 | Resistance to chemicals - Brake fluid |
| VW TL 260 No.2.9 | Resistance to chemicals - Coolant |
| VW TL 260 par.3.6 | Coating thickness |
| VW TL 260 par.3.7 | Adhesion |
| VW TL 260 par.3.8 | Stone-chip resistance |
| VW TL 52038 | Adhesive Labels |
| VW TL 52217 | Artificial Weathering in the Vehicle Exterior Requirements |
| VW TL 52223 par.5.8 | Tensile strength perpendicular to face |
| VW TL 52311 No. 2.1 | FTIR analysis |
| VW TL 52311 No. 2.10 | Notched impact strength (dry conditioned) |
| VW TL 52311 No. 2.3.1 | Isopropanol |
| VW TL 52311 No. 2.3.2 | Sodium hydroxide solution |
| VW TL 52311 No. 2.3.3 | Water |
| VW TL 52311 No. 2.3.4 | Artificial bird droppings |
| VW TL 52311 No. 2.3.5 | Tree resin |
| VW TL 52311 No. 2.3.6 | FAM test fuel |
| VW TL 52311 No. 2.3.7 | E10 gasoline |
| VW TL 52311 No. 2.3.8 | Sulfuric acid |
| VW TL 52311 No. 2.3.9 | Hydrochloric acid |
| VW TL 52311 No. 2.7 | Flexural strength, humid conditioned |
| VW TL 52311 No. 2.8 | Modulus of elasticity (humid conditioned) |
| VW TL 52311 No. 2.9 | Impact strength (dry conditioned) |
| VW TL 52622 Tab.1 No.1.1 | FTIR analysis |
| VW TL 52622 Tab.1 No.2.1.1 | Resistance to chemicals: Isopropanol |
| VW TL 52622 Tab.1 No.2.1.2 | Resistance to chemicals: 5% NaOH |
| VW TL 52622 Tab.1 No.2.1.3 | Resistance to chemicals: Water (grade 3) |
| VW TL 52622 Tab.1 No.2.1.4 | Resistance to chemicals: Artificial bird droppings |
| VW TL 52622 Tab.1 No.2.1.5 | Resistance to chemicals: Tree resin |
| VW TL 52622 Tab.1 No.2.10 | Color/gloss level |
| VW TL 52622 Tab.1 No.2.2.1 | Kalahari simulation (PV3929) |
| VW TL 52622 Tab.1 No.2.2.2 | Florida simulation (PV3930) |
| VW TL 52622 Tab.1 No.2.3 | Density |
| VW TL 52622 Tab.1 No.2.4 | Shore A hardness |
| VW TL 52622 Tab.1 No.2.5 | Long-term behavior at low temperatures |
| VW TL 52622 Tab.1 No.2.6 | Bond strength |
| VW TL 52622 Tab.1 No.2.7 | Test for interactions in the hard/soft compounds |
| VW TL 52622 Tab.1 No.2.8 | Aging resistance |
| VW TL 52622 Tab.1 No.2.9 | Environmental cycle test (PV1200) |
| VW TL 52631 Tab.1 No.1.1 | Materials and filler contents |
| VW TL 52631 Tab.1 No.2.1 | Material FTIR analysis |
| VW TL 52631 Tab.1 No.2.2 | Filler content TGA |
| VW TL 52631 Tab.1 No.2.3 | Ball drop test |
| VW TL 52631 Tab.1 No.2.4 | Resistance to chemicals |
| VW TL 52631 Tab.1 No.2.5 | Resistance to aging @ 150°C |
| VW TL 52631 Tab.1 No.2.6.1 | Kalahari simulation as per PV 3929 |
| VW TL 52631 Tab.1 No.2.6.2 | Florida simulation as per PV 3930 |
| VW TL 52631 Tab.1 No.2.7 | Density |
| VW TL 52631 Tab.1 No.2.8.1 | Flexural strength and modulus of elasticity @ 23°C |
| VW TL 52631 Tab.1 No.2.8.2 | Flexural strength and modulus of elasticity @ 80°C |
| VW TL 52631 Tab.1 No.2.9 | Notched impact strength |
| VW TL 52631 Tab.1 No.3.1 | Color measurement |
| VW TL 52631 Tab.1 No.3.2 | Gloss level measurement |
| VW TL 52631 Tab.1 No.3.3 | Grain, visual evaluation |
| VW TL 52660 No.2.10 | Impact strength |
| VW TL 52660 No.2.6 | Aging resistance |
| VW TL 52660 No.2.9 | Flexural strength with modulus of elasticity |
| VW TL 52671 Tab.1 No.2.1 | FTIR analysis |
| VW TL 52671 Tab.1 No.2.10 | Heat aging |
| VW TL 52671 Tab.1 No.2.3 | Density |
| VW TL 52671 Tab.1 No.2.4 | Stress crack resistance |
| VW TL 52671 Tab.1 No.2.5 | Charpy impact strength |
| VW TL 52671 Tab.1 No.2.6 | Notched impact strength |
| VW TL 52671 Tab.1 No.2.7 | Flexural strength |
| VW TL 52671 Tab.1 No.2.8 | Dimensional stability under heat - Vicat |
| VW TL 52671 Tab.1 No.2.9 | Environmental cycle test as per PV1200 |
| VW TL 52671:2009-04 | PMMA, High Gloss Trims for the Exterior |
| VW TL 527 Tab.1 No.1 | ABS - Density |
| VW TL 527 Tab.1 No.2 | ABS - Flexural strength |
| VW TL 527 Tab.1 No.3 | ABS - Flexural modulus E |
| VW TL 527 Tab.1 No.4.1 | ABS - Notched impact strength |
| VW TL 527 Tab.1 No.5 | ABS - Impact strength |
| VW TL 527 Tab.1 No.6 | ABS - Dimensional stability under heat according to Vicat |
| VW TL 52711 No.10 par.6.10 | Resistance to chemicals |
| VW TL 52711 No.5 par.6.5 | Aging resistance |
| VW TL 52711 No.6 par.6.6 | Bending stiffness |
| VW TL 52711 No.7 par.6.7 | Stone-chip resistance |
| VW TL 52711 No.8 par.6.8 | Pressure washer test |
| VW TL 52711 No.9 par.6.9 | Water absorption |
| VW TL 528 Tab2 Par.1 | Matte and semi-gloss chrome surfaces-High-gloss chrome surfaces |
| VW TL 528 Tab2 Par.2.1-2.5 | Coating thickness |
| VW TL 528 Tab2 Par.2.6 | Change in potential between microporous nickel-gloss nickel (or satin nickel) |
| VW TL 528 Tab2 Par.2.7 | Change in potential between gloss nickel (or satin nickel)-semi-gloss nickel |
| VW TL 528 Tab2 Par.2.8 | Pore Density |
| VW TL 528 Tab2 Par.3.1 | Cross-cut test (St. Andrew s cross) |
| VW TL 528 Tab2 Par.3.2 | Relative peel resistance |
| VW TL 528 Tab2 Par.4.1 | Dimension Stability under heat |
| VW TL 528 Tab2 Par.4.2 | Environmental cycle test |
| VW TL 528 Tab2 Par.5.1 | Corrosion test: Copper-accelerated acetic acid salt spray (CASS) test |
| VW TL 528 Tab2 Par.5.2 | Enviromental cycle test PV 1200 + neutral salt spray test ISO 9227 |
| VW TL 528 Tab2 Par.5.3.1 A | Corrosion testing as PV 1073-A (resistance to undiluted calcium chloride) |
| VW TL 528 Tab2 Par.5.3.1 B | Corrosion testing as PV 1073-B (resistance to locally accelerated nickel corrosion) |
| VW TL 528 Tab2 Par.5.3.2 + VW 96380 – variant 1, 6 cycles | Test corrosion VW 96380 – variant 1, 6 cycles |
| VW TL 528 Tab2 Par.5.3.2 + VW 96380 – variant 2, 1 cycles | Corrosion test VW 96380 – variant 2, 1 cycles |
| VW TL 591 section 3.2 | Appearance |
| VW TL 591 Tab.1 No.1 | Dimensional stability - Vicat |
| VW TL 591 Tab.1 No.2 | Charpy impact strength |
| VW TL 591 Tab.1 No.3 | High-temperature behavior |
| VW TL 591 Tab.1 No.4 | Low-temperature behavior |
| VW TL 591 Tab.1 No.6 | Stress crack resistance |
| VW TL 909 | Headlamps |
| VW TL 956 section 7.1 | Tightness by means of overpressure |
| VW TL 956 section 7.12 | Dust test |
| VW TL 956 section 7.4.3.1 | Resistance to reagents |
| VW TL 956 section 7.4.3.2 | Resistance to stress cracks |
| VW TL 956 section 7.6 | Forced-air aging without load |
| VW TL 956 section 7.7 | Forced-air aging with load |
| VW TL 956 section 7.8 | Corrosion resistance |
| WHIRLPOOL GES0196 rev.C | CYCLIC CORROSION Global Cyclic Corrosion Procedure |
| XP A 35-037-1 par.7.1 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Overall diameter |
| XP A 35-037-1 par.7.2 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Straightness |
| XP A 35-037-1 par.7.4.1 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Weight of protection product per unit length |
| XP A 35-037-1 par.7.5.1 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Sheath thickness (one cross section) |
| XP A 35-037-1 par.7.5.10 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Resistance to ionizing radiation |
| XP A 35-037-1 par.7.5.11 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Resistance after exposure at temperature |
| XP A 35-037-1 par.7.5.13 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Resistance to shocks |
| XP A 35-037-1 par.7.5.2 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Sheath weight per unit length |
| XP A 35-037-1 par.7.5.5 +D6.1 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Leaktightness static test |
| XP A 35-037-1 par.7.5.6 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Initial resistance to friction |
| XP A 35-037-1 par.7.5.8 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Stress cracking strength |
| XP A 35-037-1 par.7.5.9 | Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Immersion temperature and duration:+23°C-168hours |